If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I find out whats the interface address.
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Folks;
I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it.
Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card?
I... (1 Reply)
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT SUSE
set_color
set_color(1) fish set_color(1)NAME
set_color - set_color - set the terminal color
set_color - set the terminal color
Synopsis
set_color [-v --version] [-h --help] [-b --background COLOR] [COLOR]
Description
Change the foreground and/or background color of the terminal. COLOR is one of black, red, green, brown, yellow, blue, magenta, purple,
cyan, white and normal.
o -b, --background Set the background color
o -c, --print-colors Prints a list of all valid color names
o -h, --help Display help message and exit
o -o, --bold Set bold or extra bright mode
o -u, --underline Set underlined mode
o -v, --version Display version and exit
Calling set_color normal will set the terminal color to whatever is the default color of the terminal.
Some terminals use the --bold escape sequence to switch to a brighter color set. On such terminals, set_color white will result in a grey
font color, while set_color --bold white will result in a white font color.
Not all terminal emulators support all these features. This is not a bug in set_color but a missing feature in the terminal emulator.
set_color uses the terminfo database to look up how to change terminal colors on whatever terminal is in use. Some systems have old and
incomplete terminfo databases, and may lack color information for terminals that support it. Download and install the latest version of
ncurses and recompile fish against it in order to fix this issue.
Version 1.23.1 Sun Jan 8 2012 set_color(1)