My WS boot disk has failed so when i want to boot system (by OK boot -s or Ok boot disk0 ) i get these mesgs:
disk read error
boot :can not find misc/sparc9v/krtld
boot:error loading interperetor (misc/sparc9v/krtld)
Elf64 read error.
boot failed.
although it's probed ,finally i try... (1 Reply)
Hi All,
Seems to be one of the disk has failed on my Solaris server.
How do i confirm that disk has really failed or not?
Here are alert details.
-------
iostat -En out/put
c1t3d0 Soft Errors: 1884 Hard Errors: 153 Transport Errors: 54
Vendor: FUJITSU Product:... (3 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
I have an oldish Solaris 10 system (SunFire x4240), which due to a recent heating event in the server room, lost it's system disk.
I have rsync backups of all the other (data) disks, but apparently I do not have a backup of /. :-( I can start the machine up in failsafe mode, but running fsck on... (4 Replies)
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
Hi
Please can you help me on replacing or removing a faulty disk drive on a SUN NETRA X4250server with 4 internal drives only.
the format comand show me the following:
format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <drive type unknown>
... (9 Replies)
Discussion started by: fretagi
9 Replies
LEARN ABOUT NETBSD
ataraid
ATARAID(4) BSD Kernel Interfaces Manual ATARAID(4)NAME
ataraid -- software BIOS RAID
SYNOPSIS
pseudo-device ataraid
ld* at ataraid? vendtype ? unit ?
DESCRIPTION
The ataraid driver provides support for BIOS-based software RAID controllers. These are devices which have some simple support for several
basic RAID levels (often RAID 0 and RAID 1), but which require software support to actually perform the RAID function. The BIOS support is
largely just to create and recognize the array so that it may be a boot device.
The driver currently supports RAID formats from:
o Adaptec HostRAID (found in Intel 6300ESB)
o Intel MatrixRAID
o JMicron RAID
o nVidia MediaShield
o Promise FastTrak
o Via V-RAID (found in many VIA-based motherboards)
Status of the logical disk as well as the disks associated with it, can be viewed through the bioctl(8) utility.
SEE ALSO ld(4), bioctl(8)HISTORY
The ataraid driver first appeared in NetBSD 2.0.
AUTHORS
The ataraid driver was originally adapted from FreeBSD by Jason Thorpe <thorpej@NetBSD.org>.
BUGS
Not all features of the software RAID are currently recognized or supported. For example, the Adaptec support doesn't recognize when a RAID
1 should be in a ``building'' state, and it does not do the right thing.
At least part of the reason for this is that the publically-available information on these formats is quite limited.
BSD September 16, 2008 BSD