09-10-2012
It was the "Telco in a Box", in the 1995 issue of Electronics Now. Unfortunately I don't have that anymore, and don't see the article available online anywhere.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
2. UNIX for Advanced & Expert Users
Can anybody help me?
I am developing a utility for automating message paging to a BT alphanumeric pager.
I am using a USR 56K Fax-modem connected to /dev/cuab on a Sun Ultra-10. I am using the UNIX 'tip' utility to connect to the modem and I have configured the modem as follows: Baud Rate:... (2 Replies)
Discussion started by: mybeat
2 Replies
3. UNIX for Dummies Questions & Answers
Hello, everyone. I have a little favor to ask. Me and my friends decided sharing an ADSL line with four PCs.
PC no.1: Desktop, two netcard (2000 and 8139), Mandrake 9.0
PC no.2: Acer notebook, PC Card, RTL-8139C/8139C+, MS 98 + Win 2000 Pro
PC no.3: Desktop, net card 8139, WindowME + Win 2000... (1 Reply)
Discussion started by: HOUSCOUS
1 Replies
4. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
5. UNIX for Dummies Questions & Answers
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies
6. AIX
I configured the serial modem in my P6-550 AIX 5.3 box
But i dont have telephone line.
when I run the command
# cu -l /dev/tty1
the output is as follows
does it mean that my modem is responding to the command?
can i say my serial port is working and communicating fine?
Connected
... (3 Replies)
Discussion started by: pchangba
3 Replies
7. Solaris
Hi everyone,
I am hoping anyone of you could help me in this weird problem we have in 1 of our Solaris 10 servers. Lately, we have been having some ftp problems in this server. Though it can ping any server within the network, it seems that it can only ftp to a select few. For most servers, the... (4 Replies)
Discussion started by: labdakos
4 Replies
8. Hardware
Hello,
I want to connect a VT520 terminal to p3 linux box.
I have two questions regarding the connection. First,
is it possible to use RJ45 instead of RS232
cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter).
Second point is that; do i need null modem cable or
straight cable... (5 Replies)
Discussion started by: vectrum
5 Replies
LEARN ABOUT MOJAVE
pod::simple::debug
Pod::Simple::Debug(3pm) Perl Programmers Reference Guide Pod::Simple::Debug(3pm)
NAME
Pod::Simple::Debug -- put Pod::Simple into trace/debug mode
SYNOPSIS
use Pod::Simple::Debug(5); # or some integer
Or:
my $debuglevel;
use Pod::Simple::Debug ($debuglevel, 0);
...some stuff that uses Pod::Simple to do stuff, but which
you don't want debug output from...
$debug_level = 4;
...some stuff that uses Pod::Simple to do stuff, but which
you DO want debug output from...
$debug_level = 0;
DESCRIPTION
This is an internal module for controlling the debug level (a.k.a. trace level) of Pod::Simple. This is of interest only to Pod::Simple
developers.
CAVEATS
Note that you should load this module before loading Pod::Simple (or any Pod::Simple-based class). If you try loading Pod::Simple::Debug
after &Pod::Simple::DEBUG is already defined, Pod::Simple::Debug will throw a fatal error to the effect that "it's s too late to call
Pod::Simple::Debug".
Note that the "use Pod::Simple::Debug ($x, somenum)" mode will make Pod::Simple (et al) run rather slower, since &Pod::Simple::DEBUG won't
be a constant sub anymore, and so Pod::Simple (et al) won't compile with constant-folding.
GUTS
Doing this:
use Pod::Simple::Debug(5); # or some integer
is basically equivalent to:
BEGIN { sub Pod::Simple::DEBUG () {5} } # or some integer
use Pod::Simple ();
And this:
use Pod::Simple::Debug ($debug_level,0); # or some integer
is basically equivalent to this:
my $debug_level;
BEGIN { $debug_level = 0 }
BEGIN { sub Pod::Simple::DEBUG () { $debug_level }
use Pod::Simple ();
SEE ALSO
Pod::Simple
The article "Constants in Perl", in The Perl Journal issue 21. See <http://interglacial.com/tpj/21/>
SUPPORT
Questions or discussion about POD and Pod::Simple should be sent to the pod-people@perl.org mail list. Send an empty email to
pod-people-subscribe@perl.org to subscribe.
This module is managed in an open GitHub repository, <https://github.com/theory/pod-simple/>. Feel free to fork and contribute, or to clone
<git://github.com/theory/pod-simple.git> and send patches!
Patches against Pod::Simple are welcome. Please send bug reports to <bug-pod-simple@rt.cpan.org>.
COPYRIGHT AND DISCLAIMERS
Copyright (c) 2002 Sean M. Burke.
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
This program is distributed in the hope that it will be useful, but without any warranty; without even the implied warranty of
merchantability or fitness for a particular purpose.
AUTHOR
Pod::Simple was created by Sean M. Burke <sburke@cpan.org>. But don't bother him, he's retired.
Pod::Simple is maintained by:
o Allison Randal "allison@perl.org"
o Hans Dieter Pearcey "hdp@cpan.org"
o David E. Wheeler "dwheeler@cpan.org"
perl v5.18.2 2013-11-14 Pod::Simple::Debug(3pm)