I am trying to reconstruct a failed 4 disk RAID5 Western Digital ShareSpace device using 3 of the 4 disks connected via USB to an Ubuntu 12.04 machine. I get what seems like a successful re-assemble from -
Can sed be used to take a existing record and reverse the order of defined character placement if there is no delimeters?
existing record:
0123456789CO
expected result:
9876543210CO
if there were delimeters I could define the delimeter and each placement would have an id which I... (1 Reply)
Hello, I am aware that our system has two hard drives with raid but i'm not sure as to the type of raid the system uses.
I tried this.
# df
Filesystem 512-blocks Free %Used Iused %Iused Mounted on
/dev/hd4 229376 76272 67% 6748 12% /
/dev/hd2 3080192... (1 Reply)
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT REDHAT
raidstart
raidstart(8) System Manager's Manual raidstart(8)NAME
raidstart, raidstop, - command set to manage md devices.
SYNOPSIS
raidstart [options] <raiddevice>*
raidstop [options] <raiddevice>*
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple disks to be combined into a single
filesystem, possibly with automated backup and recovery. Linux RAID devices are implemented through the md device driver.
If you're using the /proc filesystem, /proc/mdstat gives you informations about md devices status.
Currently, Linux supports linear md devices, RAID0 (striping), RAID1 (mirrroring), and RAID4 and RAID5. For information on the various lev-
els of RAID, check out:
http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/
for new releases of the RAID driver check out:
ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha
Avaible commands are :
mkraid : configures (creates) md (RAID) devices in the kernel, banding multiple devices into one.
raidstart : activates (starts) an existing 'persistent' md device
raid0run : activates old nonpersistent RAID0/LINEAR md devices
raidstop : turns off an md device, and unconfigures (stops) it
By default, a systems RAID configuration is kept in /etc/raidtab, which can configure multiple RAID devices.
All of these tools work similiarly. If -a (or --all) is specified, the specified operation is performed on all of the RAID devices men-
tioned in the configuration file. Otherwise, one or more RAID devices must be specified on the command line. For example:
raid0run -a
Starts all of the 'old' RAID0 RAID devices specified in /etc/raidtab. If only /dev/md1 should be started, the following command should be
used instead:
raidstart /dev/md1
OPTIONS -a, --all
Apply the command to all of the configurations specified in the config file.
-c, --configfile filename
Use filename as the configuration file (/etc/raidtab is used by default).
-h, --help
Displays a short usage message, then exits.
-V, --version
Displays a short version message, then exits.
NOTES
The raidtools are derived from the md-tools and raidtools packages, which were originally written by Marc Zyngier, Miguel de Icaza, Gadi
Oxman, Bradley Ward Allen, and Ingo Molnar.
BUGS
no known bugs.
SEE ALSO raidtab(5), raid0run(8), raidstop(8), mkraid(8)raidstart(8)