Hello,
I am trying to write a bash script function to present the user a menu of options. The following is what I have so far:
function MainMenu {
while ]
do
echo "--------------------------------------------------------------------------------"
echo... (4 Replies)
I have a main menu
quit=n
while
do
clear
echo
echo "1. General system information"
echo "2. Hardware utilisation information"
echo "3. File management"
echo "4. User information"
echo "5. Information on network connectivity"
echo "6. Information on processes"
echo "Q.Quit" ... (3 Replies)
Greetings all,
I'm having some trouble writing a menu drive bash script, actually coding the menu part was not difficult however its a problem with a menu option I'm having trouble with.
My menu has 5 options, when the user selects the second option, they are then prompted to enter a number from... (5 Replies)
Dear Sir,
May I know how do I go about adding the following feature into the script below:
When user enter values other than 1,2,3,4,
a) Message “Wrong entry !!! Pls select 1,2,3 or 4” is displayed
b) The screen is cleared again and the menu is displayed.
#!/bin/bash
clear
var=1... (2 Replies)
Hi,
In the archives I found this:
And this works fine.
$if mode=vi
"\C-0-": digit-argument
TAB: menu-complete
"\e
But what I want is to reverse this. So I want that tab does reverse menu completion and shift tab does normal menu completion.
Can anyone help me with this? Thanks (0 Replies)
Hello,
Been trying to build a menu with whiptail lately. However, my code doesn't seems to be working even though when i compared to other similar code they looks the same.
#!/bin/bash
clear
whiptail --msgbox "Entering networking sub-menu" 20 78
whiptail --title Networking --menu... (8 Replies)
Ever since I added these two code blocks to my bash menu it just opens and closes right away. I use a batch file that worked fine until these codes were added and I am not sure what is wrong.
Basically, what I am trying to do in the additional section is if the answer is "Y" then it goes back... (13 Replies)
The perl command is not executing? I am trying to run the .pl in my cygwin home directory (C:\cygwin\home\cmccabe) using ${id}.txt.hg19_multianno.txt (located in the annovar directory) as the input file to be formatted and $FILENAME is the output file to be saved. The .pl is attached as... (8 Replies)
We have a simple menu with prompt of menu numbers to user.
It is still under construction.
Is there a way to "count" the menu choices so the prompt maximum count can be changed dynamically?
See attached TODO note in code
read_options(){
local choice
# the... (7 Replies)
Hi, I'm new to bash, and have an example menu script using Zenity. It works fine if the user enters A B or C, but if the user enters nothing, I can only figure out how to exit the script. How do I get the menu to reappear if no input is selected?
The script is:
title="Select example"... (2 Replies)
Discussion started by: allen11
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)