08-15-2012
10 More Discussions You Might Find Interesting
1. Solaris
Hello
We have a power supply in an x4100 (x86) and it seems to be faulty but it is still working!?! (this box only has one PSU). We are getting Orange flashing warning light on the front of the box and the LED labelled “rear PSu” is solid orange ...We don't seem to have had any syslog error... (8 Replies)
Discussion started by: hcclnoodles
8 Replies
2. Solaris
I have a question here about the OS logs (/var/adm/messages) where it should write most alarms.
I ran a hardware test by showing the Power Supply redundancy. Removing PS0 while PS1 is still plugged in confirms that the system still operates with no problems. However, when it comes to logging, I... (1 Reply)
Discussion started by: gilberteu
1 Replies
3. Solaris
Hi
Ive been facing a prob today in SAP which is been installed in solaris .the prob is one of my file systems tat is /usr/sap/psu is gettin full.i chkd the file named core which gets generated so i was asked to delete that file after doing tat my file systems space was 90%,but the prob is that... (0 Replies)
Discussion started by: madanmeer
0 Replies
4. Solaris
I need to find out PSU info for some M class severs, normally prtdiag -v show's the relevant PS info, however these M classes don't seem to go down to that level !?
Anyone any ideas , no physical or console access available at this stage :(
thx... (3 Replies)
Discussion started by: itsupplies
3 Replies
5. Solaris
Hi all,
I have one Sun Oracle T5220 server with Solaris 10.
On the front panel I saw the PSU fault led is steady with an orange color. So I checked the PSUs changed them and checked the "showfaults", "showfru" and some another commands, no problem. On the rear side I don't see any errors... (2 Replies)
Discussion started by: hubatuwang
2 Replies
6. Shell Programming and Scripting
does anyone know any shell script command that can check if PSU and fan needs to be replaced?
examples will also be greatly appreciated.
thanks! (5 Replies)
Discussion started by: h0ujun
5 Replies
7. Solaris
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Discussion started by: manalisharmabe
9 Replies
8. Red Hat
Hello,
We have a cluster and each server have 2 PSU.
An alarm should be raised in case of failure so we need to check periodically the PSU status wth a script.
The first idea was to check with ipmitool but this take some time to get the data and we face some other issues now due to that... (1 Reply)
Discussion started by: @dagio
1 Replies
9. Solaris
Hello,
When reviewing the messages log today I noted something odd, so I ran:
/usr/lib/osa/bin/healthck -a
and the response noted Failed Power Supply. Sure enough the light on the PSU is amber. Uh oh...
In an effort to see if I can figure out what kinds of PSU we have, I found a... (2 Replies)
Discussion started by: madEG
2 Replies
10. UNIX for Beginners Questions & Answers
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
LEARN ABOUT PLAN9
ddi_intr_get_supported_types
ddi_intr_get_supported_types(9F) ddi_intr_get_supported_types(9F)
NAME
ddi_intr_get_supported_types - return information on supported hardware interrupt types
SYNOPSIS
#include <sys/types.h>
#include <sys/conf.h>
#include <sys/ddi.h>
#include <sys/sunddi.h>
int ddi_intr_get_supported_types(dev_info_t *dip, int *typesp);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI)
dip Pointer to dev_info structure
typesp Pointer to supported interrupt types
The ddi_intr_get_supported_types() function retrieves the interrupt types supported by a particular hardware device and by the system soft-
ware. Upon successful return, the supported types are returned as a bit mask in the integer pointed to by the typesp argument. See
<sys/ddi_intr.h> for a list of interrupts that can be returned by a hardware device.
For PCI devices that support MSI and/or MSI-X based hardware, this interface returns only the interrupt types that are supported by all the
hardware in the path to the hardware device.
An interrupt type is usable by the hardware device if it is returned by the ddi_intr_get_supported_types() function. The device driver can
be programmed to use one of the returned interrupt types to receive hardware interrupts.
The ddi_intr_get_supported_types() function returns:
DDI_SUCCESS On success.
DDI_EINVAL On encountering invalid input parameters.
DDI_INTR_NOTFOUND Returned when the hardware device is found not to support any hardware interrupts.
CONTEXT
The ddi_intr_get_supported_types() function can be called from user or kernel non-interrupt context.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pci(4), attributes(5), pcmcia(7D), sysbus(4), ddi_intr_add_handler(9F), ddi_intr_alloc(9F), ddi_intr_enable(9F)
The ddi_intr_get_supported_types() function can be called by the device driver even at any time if the driver has added an interrupt han-
dler for a given interrupt type.
Soft interrupts are always usable and are not returned by this interface.
Any consumer of this interface should verify that the return value is not equal to DDI_SUCCESS. Incomplete checking for failure codes could
result in inconsistent behavior among platforms.
07 Apr 2005 ddi_intr_get_supported_types(9F)