Hi,
I am getting different output for grep depending which directory I am in.
The following is a transcript of my session, I am using egrep but have also used grep -E. The directory names have been changed for security:
$pwd
/dir1/dir2/dir3/dir4
$echo 000000 |egrep -v
$echo $?
1
$cd ..... (10 Replies)
I had a similar script in solaris and it had no problem. I wrote this one in freeBSD and it gave me strange output. Can anyone please tell me why? thanks a lot
#!/bin/sh
#This is a shell script that checks file system capacity mounted on /home directory
#If file system is over 90% capacity,... (1 Reply)
hi, in solaris 10 SUN SPARC V245 server the following df -h output is showing . can i reuse the following disk space by deleting them
/platform/sun4u-us3/lib/libc_psr/libc_psr_hwcap1.so.1
20G 5.2G 14G 27% /platform/sun4u-us3/lib/libc_psr.so.1... (2 Replies)
Hi
At OK> prompt, I have run the boot -s command
After system is coming on to multiuser state, when I run the " who -r" command, I get the following message
# who -r
run-level Oct 17 03:48 last=
Means I dont see "S" after run-level keyword. Could any one... (2 Replies)
I was reviewing yesterday's sar file and came across this strange output! What in the world? Any reason why there's output like that?
SunOS unixbox 5.10 Generic_144488-07 sun4v sparc SUNW,T5240 Solaris
00:00:58 device %busy avque r+w/s blks/s avwait avserv
11:20:01 ... (4 Replies)
Hi all,
After deleting some large log files on solaris 9 machine I can see strange df output shows below
/dev/vx/dsk/rootvol 45G 16384E 50G 39879076698694% /
I thought it will back to normal once I restart it but did not. I have seen in sunsolve article 6362734 that "Solaris 8... (0 Replies)
Hi,
I using tcl script to perform certain conditions. Part of the results should have average . I couldn't figure out what 's the cause as the result of the average is Zero.
Example of the case????
#!/usr/bin/tclsh
set counter 500
set total 1000
puts "Total num: $total \n"
puts ... (3 Replies)
Can someone please explain why I get two outputs with the du command? The first one gave me one. I also didn't ask for the second directory so why did it give that directory?
$ du -h "/media/Part 1/Desktop/playlist"
775M /media/Part 1/Desktop/playlist
$ du -h "/media/Part... (1 Reply)
Can someone please explain this to me?
auser:x:500:500:Anne User:/home/auser:/bin/sh
buser:x:501:501:Bob User:/home/buser:/bin/bash
I'm used to it looking like this. What is the difference between the first name and second name? In the first case I had to use the first name to change my... (3 Replies)
Hi,
Kindly help me to understand the behavior or logic of the below shell command
$ echo $!#
echo $echo $
$
$ echo !$#
echo $#
0
I am using GNU bash, version 3.2.25(1)-release (2 Replies)
Discussion started by: royalibrahim
2 Replies
LEARN ABOUT DEBIAN
wicd-wired-settings.conf
WICD-WIRED-SETTINGS.CONF(5) File Formats Manual WICD-WIRED-SETTINGS.CONF(5)NAME
wicd-wired-settings.conf - controls Wicd's wired network settings
DESCRIPTION
This file contains configuration information for wired interfaces in Wicd.
This file is located at /etc/wicd/wired-settings.conf
SETTINGS
default = <0|1>
This option decides whether to use this profile as the default. 0 = do not use this profile as default.
1 = use this profile as default.
beforescript = <None|arbitrary_script>
This defines a script to run before Wicd brings up the connection. The script should be a Bourne-compatible script and should be
executable.
IMPORTANT - scripts should ONLY be writable by root and located in a directory that is only writable by root.
afterscript = <None|arbitrary_script>
This defines a script to run after Wicd brings up the connection. The script should be a Bourne-compatible script and should be
executable.
IMPORTANT - scripts should ONLY be writable by root and located in a directory that is only writable by root.
predisconnectscript = <None|arbitrary_script>
This defines a script to run before Wicd disconnects the interface. The script should be a Bourne-compatible script and should be
executable.
postdisconnectscript = <None|arbitrary_script>
This defines a script to run after Wicd disconnects the interface. The script should be a Bourne-compatible script and should be
executable.
IMPORTANT - scripts should ONLY be writable by root and located in a directory that is only writable by root.
ip = <None|ip_address>
Use this option if you have a static ip address for your system.
netmask = <None|networkmask>
This setting is only appropriate if a static ip address is configured above.
broadcast = <None|broadcast_address>
This setting is only appropriate if a static ip address is configured above.
gateway = <None|gateway_address>
This setting is only appropriate if a static ip address is configured above.
use_static_dns = <True|False>
True = use static DNS servers instead of accepting what the dhcp server supplies.
use_global_dns = <True|False>
True = use the global DNS servers provided in wicd-manager-settings.conf(5). This option is only appropriate if "use_static_dns =
True"
dns1 = <None|ip_address>
Static DNS address if "use_static_dns = True" and "use_global_dns = False"
dns2 = <None|ip_address>
Static DNS address if "use_static_dns = True" and "use_global_dns = False"
dns3 = <None|ip_address>
Static DNS address if "use_static_dns = True" and "use_global_dns = False"
SEE ALSO wicd(8), wicd-curses(8), wicd-manager-settings.conf(5), wicd-wireless-settings.conf(5).
wicd-1.7.2.4 WICD-WIRED-SETTINGS.CONF(5)