|
|
Sponsored Content
Operating Systems
Solaris
Which gives the correct swap space top/vmstat ?
Post 302684163 by vmcore on Thursday 9th of August 2012 08:32:39 AM
08-09-2012
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there,
When I run top on my machine it says I have 497M swap space in use, and 380M swap space free,
but I have only allocated 512M swap space to the machine!!!!
Does anyone know how swap used is calculated in the top command?
Thanks... (1 Reply)
Discussion started by: chorgan
1 Replies
2. UNIX for Dummies Questions & Answers
Hi there,
I´m trying to get the information of vmstat & top in two different logfiles.
That not that difficult.
vmstat 30 >> myfile.log
top >> myfile2.log
But I also like to include a timestamp every 30 sec to be sure from what date the logs are.
For the Top command I were able to... (2 Replies)
Discussion started by: isacs
2 Replies
3. UNIX for Dummies Questions & Answers
Hello,
I would like to know if there is any difference between the pageing space and the swap space.
Thank you in advance. (1 Reply)
Discussion started by: VeroL
1 Replies
4. AIX
how do you get the paging space reduced without rebooting the machine ? the os is aix (2 Replies)
Discussion started by: aaronh
2 Replies
5. UNIX for Dummies Questions & Answers
Hi
I have checked the output of top command in which there is a difference shown between the swap of top command for a process with total swap memory usage of the top command.
Swap usage of process is higher than the total swap memory usage.
top - 18:28:21 up 7:13, 5 users, load... (2 Replies)
Discussion started by: gagan2914
2 Replies
6. Solaris
Hi all,
I have a server running an Oracle database that is part of a Solaris M5000 container. Presumably this is referred to as a zone within a cluster, not sure if I get the terminology right.
Anyway, a third-party manages the zone and unfortunately is not "helpful/friendly" to assist me on... (1 Reply)
Discussion started by: newbie_01
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
OS = Solaris 5.10
I need some guidance on interpreting vmstat to confirm whether my server is swapping or not. Can anyone please advise whether the column to check on the vmstat output is the pi column, does higher pi values means the server is swapping or am having swapping issues?
... (1 Reply)
Discussion started by: newbie_01
1 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
OS = Solaris 5.10
Without using top, can anyone please advise how to get the current swap space that is assigned to a sub-zone that is part of the Solaris zone? Some of the servers does not have the top command and I do not have access to run zone level commands either like zonecfg... (3 Replies)
Discussion started by: newbie_01
3 Replies
9. Linux
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Discussion started by: apm
1 Replies
10. UNIX for Dummies Questions & Answers
RHEL 5.4
Our Linux machine seemed to be running slow. So, I ran the top and vmstat commands.
Question1.
I can see the process 11517 consuming 100% CPU . But that just means that this process totally utilizes one of the cores in a mult-core CPU. Right ? This machine apparently has two... (2 Replies)
Discussion started by: kraljic
2 Replies
LEARN ABOUT CENTOS
rescan-scsi-bus.sh
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1) NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]] OPTIONS
-a, --alltargets scan all targets, not just currently existing [default: disabled] -d enable debug [default: 0] -l activates scanning for LUNs 0--7 [default: 0] -L NUM activates scanning for LUNs 0--NUM [default: 0] -w, --wide scan for target device IDs 0--15 [default: 0--7] -c enables scanning of channels 0 1 [default: 0 / all detected ones] -r, --remove enables removing of devices [default: disabled] -f, --flush flush failed multipath devices [default: disabled] -i, --issue-lip issue a FibreChannel LIP reset [default: disabled] -u, --update look for existing disks that have been remapped -s, --resize look for resized disks and reload associated multipath devices, if applicable --forcerescan rescan existing devices --forceremove remove and readd every device (DANGEROUS) --nooptscan don't stop looking for LUNs is 0 is not found --color use coloured prefixes OLD/NEW/DEL --hosts=LIST scan only host(s) in LIST --channels=LIST scan only channel(s) in LIST --ids=LIST scan only target ID(s) in LIST --luns=LIST scan only lun(s) in LIST --sync, --nosync issue a sync / no sync [default: sync if remove] --attachpq3 tell kernel to attach sg to LUN 0 that reports PQ=3 --reportlun2 tell kernel to try REPORT_LUN even on SCSI2 devices --largelun tell kernel to support LUNs > 7 even on SCSI2 devs --sparselun tell kernel to support sparse LUN numbering Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended). LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.) SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi sg3_utils Homepage: http://sg.danny.cz/sg rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)