Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hello,
Is there any API or any other approach to detect whether the network cable is connected to the network adapter, say, en0, en1 or en2?
The OS is AIX6.1.
Thank you. (4 Replies)
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT FREEBSD
boot.config
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO boot(8), loader(8)AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD May 13, 2007 BSD