No network cable But Network interface is UP and Running
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hello,
Is there any API or any other approach to detect whether the network cable is connected to the network adapter, say, en0, en1 or en2?
The OS is AIX6.1.
Thank you. (4 Replies)
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MINIX
liebert
LIEBERT(8) NUT Manual LIEBERT(8)NAME
liebert - Driver for Liebert contact-closure UPS equipment
NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
You may have to build another cable with DTR connected through to the UPS for it to work.
There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
fundamental limitation of any contact-closure driver.
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 LIEBERT(8)