Cloning can be quite tricky. Often the disk devices which are restored are all wrong for the new platform. However, if it's the boot archive that the system is complaining about then update that first. Boot archive architecture wasn't used after Solaris 10u3 so I guess your version is 10u3 or earlier.
Boot from CD and mount your harddisk root filesystem under /a
then.....
Then take the system down. On first attempted boot from hard disk ensure you use the -r switch to tell Solaris to reconfigure.
Post the results of that. As I said above, we might need to rebuild all filesystem devices.
I once found a document on the web describing how to build partition flar images instead of having just the one large one.
I have managed this but am having problems extracting the subsequent flar archives.
I ahve built the system from a jumpstart server and now need to add the program images etc... (0 Replies)
I have a Sun T5120, and I want to programmatically determine how much RAM it has.
# uname -a
SunOS myhost 5.10 Generic_141444-09 sun4v sparc SUNW,SPARC-Enterprise-T5120
The box has 64Gb; I tried prtdiag and prtconf, but they give me bogus info
prtconf gives me:
# prtconf |grep -i... (12 Replies)
Hi admins,
As we can create flash archieve on solaris with flarcreate command utility,
so is there any utility like this on Linux to create flah archieves ?? (10 Replies)
Hi,
can someone help with the following?
I got 1x146GB disk which is span by just one zfs rpool.
When issue for example:
as you can see in above output the flar is very small, just around 10KB
rpool with all data sets has several GB so this can't be good image. This is on the Solaris 10... (3 Replies)
Hi,
First sorry for my english !
I'm a newbie on Solaris and I'm trying to clone a SUN T5220 (sun4V platform) on SUN V240 (sun4u platform) using ufsdump/ufsrestore.
Dumping all filesystem and restoring it on the V240 box and Make the disk bootable using installboot command.
When... (21 Replies)
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
Hi everyone,
We have the below sun Operating system, Now our storage team have Create a 500GB LUN for this server, How can i scan and mount the shared LUN ? Could anyone help me to resolve this issue.
SunOS my_hostname.com 5.10 Generic_150400-09 sun4v sparc sun4v
Update:
--------
I... (9 Replies)
Hi experts,
This is a production server.
Host information's are below
SunOS hostname_srv 5.10 Generic_150400-09 sun4v sparc sun4v
Now issue with ntp service, This host have zone in it with 9 hosts, Every hosts have ntp service issue. While i check for the service status it's in... (3 Replies)
Hi
I have systems running UFS and ZFS file system type, and I need to create images of them ( in HP-UX ) we call it ignite, but in my case I dont have tape drives attached to the servers. I have read about flar archives, but the do I have to create those images in single user mode or using the... (8 Replies)
Discussion started by: fretagi
8 Replies
LEARN ABOUT OPENDARWIN
prtdiag
prtdiag(1M)prtdiag(1M)NAME
prtdiag - display system diagnostic information
SYNOPSIS
/usr/sbin/prtdiag [-v] [-l]
prtdiag displays system configuration and diagnostic information on sun4u and sun4v systems.
The diagnostic information lists any failed field replaceable units (FRUs) in the system.
The interface, output, and location in the directory hierarchy for prtdiag are uncommitted and subject to change in future releases.
prtdiag does not display diagnostic information and environmental status when executed on the Sun Enterprise 10000 server. See the
/var/opt/SUNWssp/adm/${SUNW_HOSTNAME}/messages file on the system service processor (SSP) to obtain such information for this server.
The following options are supported:
-l Log output. If failures or errors exist in the system, output this information to syslogd(1M) only.
-v Verbose mode. Displays the time of the most recent AC Power failure, and the most recent hardware fatal error information, and (if
applicable) environmental status. The hardware fatal error information is useful to repair and manufacturing for detailed diagnos-
tics of FRUs.
The following exit values are returned:
0 No failures or errors are detected in the system.
1 Failures or errors are detected in the system.
2 An internal prtdiag error occurred, for example, out of memory.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWkvm |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable* |
+-----------------------------+-----------------------------+
*The output is unstable.
modinfo(1M), prtconf(1M), psrinfo(1M), sysdef(1M), syslogd(1M), attributes(5), openprom(7D)NOTES
Not all diagnostic and system information is available on every Solaris platforn, and therefore cannot be displayed by prtdiag. On those
platforms, further information can be obtained from the System Controller.
29 Aug 2005 prtdiag(1M)