|
|
Sponsored Content
Operating Systems
AIX
Configure VIOS SEA w. load sharing
Post 302680553 by funksen on Thursday 2nd of August 2012 03:54:21 AM
08-02-2012
never tried such a configuration, since we migrate almost everything to blade now, and they just have one vio server each, it's been a long time I configured a sea over two vios
maybe the problem comes with the etherchannel? you wrote you use 2 10gbit interfaces on each vio
do you use an active backup configuration, round robin active active or lacp? I had big problems with 10gbit lacp, so we had to switch to active backup
you could try to remove the etherchannel, and create the sea with one physical adapter, just for troubleshooting
if you don't use etherchannel at all, forget this post..
maybe the problem comes with the etherchannel? you wrote you use 2 10gbit interfaces on each vio
do you use an active backup configuration, round robin active active or lacp? I had big problems with 10gbit lacp, so we had to switch to active backup
you could try to remove the etherchannel, and create the sea with one physical adapter, just for troubleshooting
if you don't use etherchannel at all, forget this post..
|
|
9 More Discussions You Might Find Interesting
1. IP Networking
I have RedHat 9.0 installed on three of my servers (PIII - 233MHz) and want that they share a common IP address so that any request made reaches each of the servers.
Can anyone suggest how should I setup my LAN. I'm new to networking in Linux so please elaborate and would be thankful for a timely... (2 Replies)
Discussion started by: Rakesh Ranjan
2 Replies
2. Shell Programming and Scripting
hi all
need your help.
I am wrting a script that will load data into the table.
then on another load will append the data into the existing table.
Regards
Ankit (1 Reply)
Discussion started by: ankitgupta
1 Replies
3. AIX
I am trying to create a SEA on a LHEA port and it gives me error
lsdev -Cc adapter:
ent0 logical host ethernet port (l-hea)
ent1 virtual I/O ethernet adapter
mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199
method error (/usr/lib/methods/cfgsea):
Failed to configure SEA... (0 Replies)
Discussion started by: filosophizer
0 Replies
4. AIX
Hi Guys,
I'm getting the below error while trying to create a SEA adapter in VIOS
$ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1
... (4 Replies)
Discussion started by: kkeng808
4 Replies
5. AIX
Hi experts, i got a 4-port Adapter card on VIOS and would like to configure 4SEA for 4 difference segment IP client's LPAR use, first SEA succeed to be configured on ent0 but once second SEA configured, first SEA fail to be connected. Any issues i need to be concerned in order to configure 4 SEA on... (8 Replies)
Discussion started by: polar
8 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Sorry guys but let me start off by saying I am an AIX noob! I am running AIX 6.1 and recently purchased two iSCSI TOE cards. The plan is to connect these two cards to a Dell EqualLogic SAN and that has two volumes configured for logs and data.
The point of the two cards is to do load balancing... (21 Replies)
Discussion started by: cbrinker
21 Replies
8. Shell Programming and Scripting
Suppose i have 3 different servers say x,y and z.
Im running some process say ABC and 40 instances for the same is being created.
In load sharing suppose on
server x, 20 instances are running
server y, 10 instances are running
server z, 10 instances are running.
While checking the... (1 Reply)
Discussion started by: ankitknit
1 Replies
9. AIX
Hello,
I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time.
Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
LEARN ABOUT OPENSOLARIS
dfstab
dfstab(4) File Formats dfstab(4) NAME
dfstab - file containing commands for sharing resources across a network DESCRIPTION
dfstab resides in directory /etc/dfs and contains commands for sharing resources across a network. dfstab gives a system administrator a uniform method of controlling the automatic sharing of local resources. Each line of the dfstab file consists of a share(1M) command. The dfstab file can be read by the shell to share all resources. System administrators can also prepare their own shell scripts to execute particular lines from dfstab. The contents of dfstab put into effect when the command shown below is run. See svcadm(1M). /usr/sbin/svcadm enable network/nfs/server SEE ALSO
share(1M), shareall(1M), sharemgr(1M), svcadm(1M) NOTES
Do not modify this file directly. This file is reconstructed and only maintained for backwards compatibility. Configuration lines could be lost. Use the sharemgr(1M) command for all share management. SunOS 5.11 15 Aug 2008 dfstab(4)