08-01-2012
I do not have your hardware at hand, so the advice tends to be a bit general.
Having said this: is your PCI-X SCSI-Adapter RAID-capable at all? "SCSI" is a way to connect disks, whereas "RAID" is a way to organize several physical disks into one big logical disk. A SCSI adapter doesn't necessarily have to be RAID-capable at all (and maybe yours isn't).
Are there any disks attached to the controller? Without (enough) disks you can't create a RAID-array, obviously.
I hope this helps.
bakunin
10 More Discussions You Might Find Interesting
1. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
2. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
3. Solaris
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
Discussion started by: nicktrix
5 Replies
4. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
5. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
9. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT NETBSD
ataraid
ATARAID(4) BSD Kernel Interfaces Manual ATARAID(4)
NAME
ataraid -- software BIOS RAID
SYNOPSIS
pseudo-device ataraid
ld* at ataraid? vendtype ? unit ?
DESCRIPTION
The ataraid driver provides support for BIOS-based software RAID controllers. These are devices which have some simple support for several
basic RAID levels (often RAID 0 and RAID 1), but which require software support to actually perform the RAID function. The BIOS support is
largely just to create and recognize the array so that it may be a boot device.
The driver currently supports RAID formats from:
o Adaptec HostRAID (found in Intel 6300ESB)
o Intel MatrixRAID
o JMicron RAID
o nVidia MediaShield
o Promise FastTrak
o Via V-RAID (found in many VIA-based motherboards)
Status of the logical disk as well as the disks associated with it, can be viewed through the bioctl(8) utility.
SEE ALSO
ld(4), bioctl(8)
HISTORY
The ataraid driver first appeared in NetBSD 2.0.
AUTHORS
The ataraid driver was originally adapted from FreeBSD by Jason Thorpe <thorpej@NetBSD.org>.
BUGS
Not all features of the software RAID are currently recognized or supported. For example, the Adaptec support doesn't recognize when a RAID
1 should be in a ``building'' state, and it does not do the right thing.
At least part of the reason for this is that the publically-available information on these formats is quite limited.
BSD
September 16, 2008 BSD