07-30-2012
Lan card not reaching Gateway
Hi,
I have this problem on RHEL box. I am using two NIC's of same model and make (Intel 82557) in the adjacent PCI slots . I am using each one for different subnet and have assigned them ipaddresses and gateways of respective subnets . While one is O.K. connecting to its gateway other don't. I have checked this card in Winows and its working fine. Card is not faulty. Problem only starts in RHEL.
ip1 192.168.14.2 -----> gateway 192.168.14.1
ip2 172.16.18.3 --X--> gateway 172.16.18.1
Any help is aprreciated.
Thanks,
Dexter
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
The Lan card in one of our UIII WS's seem doesn't work,so with ping command i can not see any of the machines in LAN and with some other tests i'm sure it's not OK.
I tried to use the second card on PCI port ,but the replaced card was one of the ordinary card for PC's ...by the way after... (1 Reply)
Discussion started by: nikk
1 Replies
2. Cybersecurity
what is lan card autonegotiation ?
how to enable and disable this feature? (2 Replies)
Discussion started by: nabil_boussetta
2 Replies
3. SCO
Dear all
Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working.
Is... (1 Reply)
Discussion started by: ccvyas
1 Replies
4. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
5. SCO
hi all
i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance .
bidhayak (3 Replies)
Discussion started by: bidhayakm
3 Replies
6. Programming
Please tell me API in Solaris / Linux / UNIX to get status information of LAN card. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies
7. Linux
Hi.
I have a lan card installed on my server. I want to check the duplex speed of it. How can I check it?
Help is appreciated.
Thank you. (3 Replies)
Discussion started by: Amol21
3 Replies
8. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
9. Red Hat
we have red hat 6 linux box
There are two lan card
one lan card eth0 have ip 10.82.190.31/24 GW 10.82.190.254
2th lan card eth1 have ip 10.82.188.33/24 GW 10.82.188.254
I have below route ... I use two route table
root@xxx# netstat -rn
Kernel IP routing table
Destination Gateway ... (5 Replies)
Discussion started by: chuikingman
5 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT CENTOS
kbdrate
KBDRATE(8) Linux Programmer's Manual KBDRATE(8)
NAME
kbdrate - reset the keyboard repeat rate and delay time
SYNOPSIS
kbdrate [ -s ] [ -r rate ] [ -d delay ]
DESCRIPTION
kbdrate is used to change the keyboard repeat rate and delay time. The delay is the amount of time that a key must be depressed before it
will start to repeat.
Using kbdrate without any options will reset the repeat rate to 10.9 characters per second (cps) and the delay to 250 milliseconds (ms) for
Intel- and M68K-based systems. These are the IBM defaults. On SPARC-based systems it will reset the repeat rate to 20 cps and the delay to
200 ms.
OPTIONS
-s Silent. No messages are printed.
-r rate
Change the keyboard repeat rate to rate cps. For Intel-based systems, the allowable range is from 2.0 to 30.0 cps. Only certain,
specific values are possible, and the program will select the nearest possible value to the one specified. The possible values are
given, in characters per second, as follows: 2.0, 2.1, 2.3, 2.5, 2.7, 3.0, 3.3, 3.7, 4.0, 4.3, 4.6, 5.0, 5.5, 6.0, 6.7, 7.5, 8.0,
8.6, 9.2, 10.0, 10.9, 12.0, 13.3, 15.0, 16.0, 17.1, 18.5, 20.0, 21.8, 24.0, 26.7, 30.0. For SPARC-based systems, the allowable
range is from 0 (no repeat) to 50 cps.
-d delay
Change the delay to delay milliseconds. For Intel-based systems, the allowable range is from 250 to 1000 ms, in 250 ms steps. For
SPARC systems, possible values are between 10 ms and 1440 ms, in 10 ms steps.
-V Display a version number and exit.
BUGS
Not all keyboards support all rates.
Not all keyboards have the rates mapped in the same way.
Setting the repeat rate on the Gateway AnyKey keyboard does not work. If someone with a Gateway figures out how to program the keyboard,
please send mail to util-linux@math.uio.no.
All this is very architecture dependent. Nowadays kbdrate first tries the KDKBDREP and KIOCSRATE ioctls. (The former usually works on an
m68k machine, the latter for SPARC.) When these ioctls fail an ioport interface as on i386 is assumed.
FILES
/etc/rc.local
/dev/port
/dev/kbd
Linux 1.1.19 22 June 1994 KBDRATE(8)