Sponsored Content
Full Discussion: LPAR Networking: Can't ping
Operating Systems AIX LPAR Networking: Can't ping Post 302673187 by PPPP on Tuesday 17th of July 2012 03:42:08 PM
Old 07-17-2012
Quote:
Originally Posted by zaxxon
Is the gateway 10.1.40.1 external ie. not an LPAR but a router? If yes, you might be missing a SEA (Shared Ethernet Adapter) to bridge the VLAN to the physical LAN. Maybe compare with the LPARs that are working, if they use a SEA.
In the output of your lsdev -Ccadapter I see no SEA listed. That could be it.
I'm 99% sure 10.1.40.1 is external because my non-LPAR systems use that gateway as well.

How do I know if an LPAR is using a SEA? I know I have a SEA because on the VIO Server...

Code:
$ lsmap -all -net
SVEA    Physloc
----- ----------------------------------------
ent2  U9110.51A.06A027D-V1-C3-T1

SEA                     ent3
Backing device          ent0
Physloc                 U788C.001.AAAA6218-P1-T1

On the LPAR that's working....
Code:
# lsdev -Ccadapter
ent0   Available         Virtual I/O Ethernet Adapter (l-lan)
ide0   Defined     01-08 ATA/IDE Controller Device
vsa0   Available         LPAR Virtual Serial Adapter
vscsi0 Available         Virtual SCSI Client Adapter

And on the LPAR that's not working:
Code:
# lsdev -Ccadapter
ent0   Available 01-08 10/100/1000 Base-TX PCI-X Adapter (14106902)
ent1   Available       Virtual I/O Ethernet Adapter (l-lan)
ide0   Available 03-08 ATA/IDE Controller Device
usbhc0 Available 02-08 USB Host Controller (33103500)
usbhc1 Available 02-09 USB Host Controller (33103500)
vsa0   Available       LPAR Virtual Serial Adapter
vscsi0 Available       Virtual SCSI Client Adapter

 

10 More Discussions You Might Find Interesting

1. AIX

LPAR and CFGMGR

I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies

2. IP Networking

ping and networking

Dear friends, Please explain the functionality of the ping command and explain the network details, and IP layers. I want some more clarification about following things i) switch ii) hub iii) routers iv) proxy (3 Replies)
Discussion started by: thangappan
3 Replies

3. AIX

LPAR

I am planning for System P with 2 number of 2-core processor (4 core in total). Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies

4. AIX

LPAR creation

can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies

5. AIX

LPAR freezes after switching of storage (lpar is mirrored)

Hi all, I have the following configuration 2 ds3524 storage disk systems located over 2 locations 2 P720 server located over 2 locations DS3524 are connected to san switch. Each vio server has 1 fc adapter attached to a san switch. per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies

6. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies

7. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies

8. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies

9. AIX

How to differentiate between a standalone LPAR and a VIOC (which again is a lpar)?

There can be configurations in IBM Server wherein a standalone partition is created on some supported IBM Server Or A VIOS - VIOC LPARs created. Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..? On a... (2 Replies)
Discussion started by: Manish00712
2 Replies

10. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device miibus device hme Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_hme_load="YES" DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces. All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and transmission of extended frames for vlan(4) and a 128-bit multicast hash filter. HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models. Cards supported by the hme driver include: o Sun PCI SunSwift Adapter (``SUNW,hme'') o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'') o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'') o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'') o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'') o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'') NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC address. Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all add-on cards except the single-port SBus versions. SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8) Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996, http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf. HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0. AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>. BSD
June 14, 2009 BSD
All times are GMT -4. The time now is 12:58 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy