|
|
Sponsored Content
Operating Systems
AIX
LPAR Networking: Can't ping
Post 302673115 by PPPP on Tuesday 17th of July 2012 12:56:41 PM
07-17-2012
|
|
10 More Discussions You Might Find Interesting
1. AIX
I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies
2. IP Networking
Dear friends,
Please explain the functionality of the ping command and explain the network details, and IP layers.
I want some more clarification about following things
i) switch
ii) hub
iii) routers
iv) proxy (3 Replies)
Discussion started by: thangappan
3 Replies
3. AIX
I am planning for System P with 2 number of 2-core processor (4 core in total).
Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies
4. AIX
can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
5. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
6. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
7. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
8. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
9. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
rds-ping
RDS-PING(1) BSD General Commands Manual RDS-PING(1) NAME
rds-ping -- test reachability of remote node over RDS SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8) utility, even though the way it works is pretty different. rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is bound; instead, the kernel processes incoming packets and responds to them. OPTIONS
The following options are available for use on the command line: -c count Causes rds-ping to exit after sending (and receiving) the specified number of packets. -I address By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address (i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source address). Using the -I option, you can override this choice. -i timeout By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds or microseconds, respectively. Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results. AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>. SEE ALSO
rds(7), rds-info(1), rds-stress(1). BSD
Apr 22, 2008 BSD