Hello,
I have two files that I need to compare and print out the line from file2 that has the first 6 fields matching the first 6 fields in file1. Complicating this are the following restrictions
1. file1 is only a few thousand lines at most and file2 is greater than 2 million
2. I need to... (7 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
input:
field1
field2
field3 field4
output:
"field1";"field2";"field3";"field4"
My input file is shown above and I want output as shown using awk. the length of field3 is fixed so, the space between field3 and field4 can vary according to the value of field3. I am new to unix, so... (1 Reply)
input:
field1
field2
field3 field4
output:
"field1";"field2";"field3";"field4"
My input file is shown above and I want output as shown using awk. the length of field3 is fixed so, the space between field3 and field4 can vary according to the value of field3. I am new to unix, so can... (5 Replies)
Hi all,
I have a single line output like below
echo $ips
10.26.208.28 10.26.208.26 10.26.208.27
want to convert above single line output as below format. Pls advice how to do ?
10.26.208.28
10.26.208.26
10.26.208.27
Regards
Kannan (6 Replies)
I am new to awk scripting.
I want to do a field by word (field) comparison of two files File1.txt and File2.txt.
The files contain a list of | (pipe) separated field.
**File 1:
-------------------
aaa|bbb|ccc|eee|fff
lll|mmm|nnn|ooo|ppp
rrr|sss|ttt|uuu|vvv**
File 2: ... (7 Replies)
Hi,
i have a scenario were i should compare a few fields from each line then increment a variable based on that.
Example file
989878|8999|Y|0|Y|N|V
989878|8999|Y|0|N|N|V
989878|8999|Y|2344|Y|N|V
i have 3 conditions to check and increment a variable on every line
condition 1 if ( $3... (4 Replies)
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)