Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: ethernet bonding
Operating Systems Linux ethernet bonding Post 302672345 by zaxxon on Monday 16th of July 2012 09:09:25 AM
Old 07-16-2012
As far as I do remember it depends a bit how to set it up on which derivate of Linux you are using. Config files etc. may be different a bit.
You might additionally have to use the command ifenslave to attach/detach NICs to a bonding device.

I move this thread to the Linux area - don't see a relation to "Infrastructure Monitoring".
 

10 More Discussions You Might Find Interesting

1. IP Networking

Bonding Internet Connections

I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Discussion started by: harley313
0 Replies

2. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

3. Red Hat

IP Bonding

Hi, What is IP bonding in Linux. What are its advantages How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies

4. IP Networking

Bonding of IP tunnels

Hello. Our Company is spreaded over Germany. There are main offices an branch offices. These offices are mostly connecte via multiple sdsl. We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances. It seemed that only one VPN Connetion between to offices could be... (0 Replies)
Discussion started by: mschwadorf
0 Replies

5. Red Hat

RHEL 5.5 NIC Bonding

I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch. The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies

6. Red Hat

Bonding a Bond with LACP

Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies

7. Red Hat

BONDING with Flapping issue!

Hi team, I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies

8. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies

9. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies

10. Red Hat

Network bonding

Dear All , Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x. After configuring , we restarted the network services , the link was down after that , we could not login in to the Server. So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies

LEARN ABOUT DEBIAN

bpqparms

BPQPARMS(8)						   Linux System Managers Manual 					       BPQPARMS(8)

NAME

       bpqparms - Configure BPQ ethernet devices.

SYNOPSIS

       bpqparms device [-a ethaddr] [-d ethaddr] [-vV]

DESCRIPTION

       Bpqparms  allows  the  setting  of  the	BPQ  Ethernet  options for a particular device. Each BPQ Ethernet device appears as a device named
       bpq0...bpqN which overlays the original Ethernet device, usually eth0...ethN. This device is an AX.25 device driver and allows AX.25 frames
       to be transmitted over an Ethernet to another machine using the same protocol. The default for the device is to send and receive BPQ Ether-
       net packets to the broadcast address. This program replaces the previous "axparms -dev" option.

OPTIONS

       -a ethaddr     Allows the setting of which ethernet address will be accepted by the BPQ Ethernet device.

       -d ethaddr     If specified on its own, will set the destination ethernet address will be used for transmitting and for	receiving  of  BPQ
		      ethernet packets. An address of "broadcast" sets it to the ethernet broadcast address.

       -v	      Displays the version number.

       -V	      The original version messages.

SEE ALSO

       ax25(4), axports(5), ifconfig(8).

AUTHOR

       Joerg Reuter DL1BKE <jreuter@poboxes.com>

Linux								 4 September 1996						       BPQPARMS(8)
All times are GMT -4. The time now is 09:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy