I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
as for the arp_ip_target I set it to the gateway address as m not using a router. Is this correct? or I shall set the other two system IPs there?
Next, I edited the interfaces file, /etc/network/interfaces:
and finally loading bonding module into the kernel and ifconfig.
if anyone has done this before, I would highly appreciate if you could tell me the exact procedure.
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)DECnet utilities March 01 2001 SETETHER(8)