I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
May I know what is the TCP/UCP port range for any default AIX NFS? Based on rpcinfo -p, I got the following output:
program vers proto port service
100000 4 udp 111 portmapper
100000 3 udp 111 portmapper
100000 2 udp 111 portmapper
100000 4 ... (4 Replies)
Hi, this is my first post...:p
Hello Admin :)
Can I have an ask for something with my configuration ?
I have finished some kind of the tutorial to build ipsec site to site, and the "step" has finished completely.
I have a simulation with a local design topology with two PC's (FreeBSD ... (0 Replies)
hello,
after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration!
I also generate different key for AH and ESP as i have shown below.
what is my problem and what should i do to have ping and test the configuration?
code:
... (0 Replies)
I want to limit all *outbound* traffic on eth0 (or all *.*) on port 25 to a specific (allowed) range...
I.E.
192.168.1.5 (local ip) tries to connect to 1.2.3.4:25 (outside real world ip)
It can proceed because 1.2.3.0/24 is the allowed range
Now, 192.168.1.5 (local ip) tries to connect to... (1 Reply)
In my Linux system ephemeral port range is showing different ranges as follows
$ cat /proc/sys/net/ipv4/ip_local_port_range
32768 61000
cat /etc/sysctl.conf | grep net.ipv4.ip_local_port_range
net.ipv4.ip_local_port_range = 9000 65500
Which will be the effective ephemeral port... (5 Replies)
I'll start with I'm not an AIX expert, I inherited a lot of AIX servers to maintain.
My problem is on AIX 7.1 TL4 SP4 environments. I'm running named as a DNS forwarder only to internal DNS servers.
These AIX servers have a customized UDP ephemeral port range to avoid conflicting with the... (0 Replies)
hi,
i would like to create a bash script that check which port in my Linux server are closed (not in use) from a specific range, port range (3000-3010).
the print output need to be only 1 port, and it will be nice if the output will be saved as a variable or in same file.
my code is:
... (2 Replies)
Discussion started by: yossi
2 Replies
LEARN ABOUT NETBSD
tftp-proxy
TFTP-PROXY(8) BSD System Manager's Manual TFTP-PROXY(8)NAME
tftp-proxy -- Internet Trivial File Transfer Protocol proxy
SYNOPSIS
tftp-proxy [-v] [-w transwait]
DESCRIPTION
tftp-proxy is a proxy for the Internet Trivial File Transfer Protocol invoked by the inetd(8) internet server. TFTP connections should be
redirected to the proxy using the pf(4) rdr command, after which the proxy connects to the server on behalf of the client.
The proxy establishes a pf(4) rdr rule using the anchor facility to rewrite packets between the client and the server. Once the rule is
established, tftp-proxy forwards the initial request from the client to the server to begin the transfer. After transwait seconds, the pf(4)
NAT state is assumed to have been established and the rdr rule is deleted and the program exits. Once the transfer between the client and
the server is completed, the NAT state will naturally expire.
Assuming the TFTP command request is from $client to $server, the proxy connected to the server using the $proxy source address, and $port is
negotiated, tftp-proxy adds the following rule to the anchor:
rdr proto udp from $server to $proxy port $port -> $client
The options are as follows:
-v Log the connection and request information to syslogd(8).
-w transwait
Number of seconds to wait for the data transmission to begin before removing the pf(4) rdr rule. The default is 2 seconds.
CONFIGURATION
To make use of the proxy, pf.conf(5) needs the following rules. The anchors are mandatory. Adjust the rules as needed for your configura-
tion.
In the NAT section:
nat on $ext_if from $int_if -> ($ext_if:0)
no nat on $ext_if to port tftp
rdr-anchor "tftp-proxy/*"
rdr on $int_if proto udp from $lan to any port tftp ->
127.0.0.1 port 6969
In the filter section, an anchor must be added to hold the pass rules:
anchor "tftp-proxy/*"
inetd(8) must be configured to spawn the proxy on the port that packets are being forwarded to by pf(4). An example inetd.conf(5) entry fol-
lows:
127.0.0.1:6969 dgram udp wait root
/usr/libexec/tftp-proxy tftp-proxy
SEE ALSO tftp(1), pf(4), pf.conf(5), ftp-proxy(8), inetd(8), syslogd(8), tftpd(8)CAVEATS
tftp-proxy chroots to /var/chroot/tftp-proxy and changes to user ``_proxy'' to drop privileges.
BSD May 31, 2007 BSD