Hi I am working on a program that reads a file with multiple columns and was curious how to specify the columns to be manipulated in the command line.
For example the file may look something like:
I would like to be able to type either "column1" or "column4" in the command line and have they print out the contents of the column put in as input as well as the contents of the two columns that follow.
Given the file above and typing "column4" on the command line, I would like the output to be:
I would greatly appreciate all help.
Thanks a lot.
Drossy
I seem to get lost when it comes in terms of Networking types and its specifications by different International bodies. I am not able to understand things like -
"synchronous operation on public data networks networking protocol"
"packet mode connected to public data networks by dedicated... (1 Reply)
I have the following sed command:
sed '/7361105/s/^\(..............................................................................................................................................................................\)....\(.*\)/\16776\2/' arch.txt > arch.tmp && mv arch.tmp arch.txt
... (4 Replies)
I wana know my box hardware specification ( Like RAM , processor speed .... Etc ) and used version of Solaris i mean (SPARC, 32-bit) or (x86, 32-bit) or(SPARC, 64-bit) or what ??
very Urgent please (5 Replies)
Hi,
anybody know how to check the system specification for the unix by using the command like the memory size, cpu's speed and etc.
Thanks. (3 Replies)
Hello Friends,
I want to use range in for loop. For that i used (..) operator but it is not working.
Ex:
for i in 1..24
do
echo $i
done
Instead of printing 1 to 24 nos, it gives o/p as: 1..24
Please help me
Thanks in advance. (2 Replies)
Hi I have a SUN box that i am supporting Model 480r . The RS card that is attached to it is giving some problems . It is pinging but i am unable to telnet into it therefore having no remote TC console access ( the system is currently up )
Is there a way by which i can remotely check the... (1 Reply)
Hi all,
Can anyone help me to get the server specifications like the following?
eg.
SUN Fire XXX
X UltraSPARC X MHZ
X MB Memory
X GB od hard disk
X On board PCI IO card
X PCI HNI card
Thanks. (4 Replies)
I am planning to implement sudo for users.
Under , it looks I have to put the users who need to have sudo access:
What are the recommended for users? I don't think I need to give the ALL privilege (i.e ) to AIX users.
I'd like to know the commonly used privilege specification for sudo... (9 Replies)
Here is the part of the script: I have modified the file name.:)
SSFILE=${My_HOME_DIR}/log/my_file_ss.log
export MM=`date '+%m'`
export DD=`date '+%d'`
export HH=`date '+%H'`
export MIN=`date '+%M'`
export HOURAGO=`echo ${HH} -1 |bc `
echo $HOURAGO
export TTIME=${MM}${DD}${HOURAGO}00... (5 Replies)
Discussion started by: N1a_Raider
5 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)