I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
LEARN ABOUT NETBSD
iy
IY(4) BSD Kernel Interfaces Manual IY(4)NAME
iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)
SYNOPSIS
iy0 at isa? port {port} irq ?
DESCRIPTION
The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.
MEDIA SELECTION
The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors. Supported media include:
AUI/DIX Standard 15 pin connector
10Base2 BNC, also known as thin-net
10BaseT UTP, also known as twisted pair
The default port to use is the port the card autodetects at ifconfig up time. To choose an alternative port, an explicit medium can be spec-
ified to ifconfig(8) or in your ifconfig.iy? file.
NOTES
The EtherExpress PRO card has no jumpers to set the address. Intel supplies software to set the address of the card in software. You have
to hardwire this address in your kernel configuration file.
SEE ALSO ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)STANDARDS
are great. There's so many to choose from.
BSD May 22, 1996 BSD