Sponsored Content
Full Discussion: ifconfig ge0 plumb
Operating Systems Solaris ifconfig ge0 plumb Post 302657311 by hicksd8 on Sunday 17th of June 2012 07:09:11 AM
Old 06-17-2012
I'd say that the driver is not seeing the card because the driver is either wrong or corrupt. Revert to card manufacturers instructions on installing the driver on this system.

Let's see what other suggestions are forthcoming from forum members.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

ifconfig

I am trying to change an IP address on a machine running HPUX10 After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas?? Thanks Brian (7 Replies)
Discussion started by: breigner
7 Replies

2. OS X (Apple)

ifconfig

Hi, I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me? Thx. (0 Replies)
Discussion started by: Jariya
0 Replies

3. Solaris

Before plumb the network interface.....

I know that I could use the #ifconfig hme0 plumb to activate the network interface. However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up? I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies

4. Shell Programming and Scripting

ifconfig!!!!

why the ifconfig command is not working in my machine? it says "-bash: ifconfig: command not found" why its says that? actually i m looking for "how can I know the Network Interface Card physical address?" Requesting u all for help. thanks (3 Replies)
Discussion started by: moco
3 Replies

5. IP Networking

/etc/hosts changes when ifconfig......

Hello everyone. Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Discussion started by: trutoman
9 Replies

6. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies

7. Linux

ifconfig - information

Hi All, I need some info on ifconfig. ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux. 1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies

8. Shell Programming and Scripting

not able to run ifconfig

Unable to run the ifconfig in my home dir.. I did add adding /sbin and /usr/sbin in th PATH But still unable to get that .. Am using red hat linux cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies

9. Solaris

Ifconfig command ?

What would be the command to remove the IP address from an interface? I want to remove the ip from this interface: ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5 inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79 ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies

10. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
GTP(4)							   BSD Kernel Interfaces Manual 						    GTP(4)

NAME
gtp -- Gemtek PCI FM radio device SYNOPSIS
gtp* at pci? flags 0x00 radio* at gtp? DESCRIPTION
The gtp driver provides support for the Gemtek PCI and Guillemot MaxiRadio FM2000 FM radio tuners. The Gemtek PCI cards are stereo FM tuners that can tune in the range 87.5 - 108.0 MHz, report signal status and stereo/mono on the current frequency, force audio output to mono, perform hardware signal search, and have an internal AFC. The card is based on the TEA5757 chip; see radio(4) for details. The flags control the driver behavior. For example, with flags 0x01 the driver will assume that a TEA5759 chip is used. SEE ALSO
intro(4), pci(4), radio(4), radio(9) HISTORY
The gtp device driver appeared in OpenBSD 3.2 and subsequently in NetBSD 1.6 wherein it replaced the mr(4) driver. AUTHORS
The gtp driver and the man page was written by Vladimir Popov <jumbo@narod.ru>. BUGS
It is impossible to determine which frequency the card is tuned to. Thus, the driver will report an internally stored value even if it is not correct (changed by some program that uses direct port access). BSD
March 26, 2011 BSD
All times are GMT -4. The time now is 11:28 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy