05-30-2012
This User Gave Thanks to jlliagre For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
2. HP-UX
I think that if the directory /tcb exists, HP-UX is in trusted mode and the passwd data is somewhere in /tcb/files/auth. But that's all I remember.
Also I think recent versions of HP-UX can have a /etc/shadow file. (0 Replies)
Discussion started by: Perderabo
0 Replies
3. Solaris
Hello All,
On solaris 10 server i could see the FTP service is in maintenance mode always :mad:
Could some assist?
svcs -xv
svc:/network/nfs/nlockmgr:default (NFS lock manager)
State: maintenance since Tue 28 Jul 2009 11:47:55 AM BST
Reason: Restarting too quickly.
See: Sun... (5 Replies)
Discussion started by: bullz26
5 Replies
4. Solaris
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
Discussion started by: JVerstry
4 Replies
5. Solaris
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies
6. Solaris
I have seen similar threads on this issue, but I have not seen a fix. Basically I am getting a lot of rcp bind errors. Below find the output of "svcs -xv". not sure where to begin:
# svcs -xv
svc:/network/rpc/bind:default (RPC bindings)
State: maintenance since Fri May 25 14:13:18 2012... (14 Replies)
Discussion started by: brownwrap
14 Replies
7. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
8. Red Hat
Hi Guys
Required help in Redhat 6.1.
After installation of Redhat 6.1 in VMware system is not going in GUI mode.
please to solve the issue...
Thanks... (5 Replies)
Discussion started by: deviltech
5 Replies
9. AIX
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
Discussion started by: Adnans2k
0 Replies
10. Solaris
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)