05-30-2012
This User Gave Thanks to jlliagre For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
2. HP-UX
I think that if the directory /tcb exists, HP-UX is in trusted mode and the passwd data is somewhere in /tcb/files/auth. But that's all I remember.
Also I think recent versions of HP-UX can have a /etc/shadow file. (0 Replies)
Discussion started by: Perderabo
0 Replies
3. Solaris
Hello All,
On solaris 10 server i could see the FTP service is in maintenance mode always :mad:
Could some assist?
svcs -xv
svc:/network/nfs/nlockmgr:default (NFS lock manager)
State: maintenance since Tue 28 Jul 2009 11:47:55 AM BST
Reason: Restarting too quickly.
See: Sun... (5 Replies)
Discussion started by: bullz26
5 Replies
4. Solaris
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
Discussion started by: JVerstry
4 Replies
5. Solaris
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies
6. Solaris
I have seen similar threads on this issue, but I have not seen a fix. Basically I am getting a lot of rcp bind errors. Below find the output of "svcs -xv". not sure where to begin:
# svcs -xv
svc:/network/rpc/bind:default (RPC bindings)
State: maintenance since Fri May 25 14:13:18 2012... (14 Replies)
Discussion started by: brownwrap
14 Replies
7. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
8. Red Hat
Hi Guys
Required help in Redhat 6.1.
After installation of Redhat 6.1 in VMware system is not going in GUI mode.
please to solve the issue...
Thanks... (5 Replies)
Discussion started by: deviltech
5 Replies
9. AIX
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
Discussion started by: Adnans2k
0 Replies
10. Solaris
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
IRSEND(1) FSF IRSEND(1)
NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)