05-27-2012
These are the types of questions I would first search Google for an answer for. And I cannot believe you wouldn't find an answer there.
When you have an answer and struggle with the specifics of it, then that's different...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
faxanswer
FAXANSWER(8) System Manager's Manual FAXANSWER(8)
NAME
faxanswer - tell a HylaFAX server to answer the telephone
SYNOPSIS
/usr/sbin/faxanswer [ -q queue-dir ] [ -h how ] modem
DESCRIPTION
faxanswer sends a message to the HylaFAX faxgetty(8) process servicing modem telling it to answer the telephone. This is useful, for exam-
ple, when a modem is used on a shared phone line and the server is configured to not normally answer the phone.
The specified modem can either be the name (typically the last component of the terminal port the modem is attached to), or the full name
of the associated FIFO named pipe file, e.g. ``FIFO.ttym2''.
OPTIONS
-q dir Use a spooling area other than /var/spool/hylafax.
-h Specify exactly how the phone should be answered. By default, the server process is instructed to answer the phone and accept
any kind of call (voice, data, fax). Discrimination of the type of call is dependent on a modem's adaptive-answer support. The
-h option can be used to force the server to answer the phone for particular type of call: one of fax, data, voice, any, extern
(to force faxgetty to invoke an external application to to handle the call), or dialX (where X is a dialstring to dial before
initiating a fax reception). If using dialX, the specified dialstring will likely need to end with a semicolon (``;'').
FILES
/var/spool/hylafax default spooling area
/var/spool/hylafax/FIFO fifo for contacting faxq
Consult hylafax-server(5) for a complete discussion of the structure and content of the spooling area.
SEE ALSO
hylafax-server(5), faxgetty(8)
May 23, 1996 FAXANSWER(8)