Sponsored Content
Full Discussion: network interface -
Special Forums IP Networking network interface - Post 302647141 by chercheur857 on Sunday 27th of May 2012 05:30:11 PM
Old 05-27-2012
network interface -

Hello,

Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?

AND

How can i desactivate an interface?


Thank you so much for help.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies

3. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies

4. Solaris

Network interface not found ?

Hello, I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else. - I dont have any /etc/hostnames.xxx - ifconfig -a shows only the loopback - kstat -c net shows only the loopback ... Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies

5. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

8. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
UBUNTU-BUILD(1) 					      General Commands Manual						   UBUNTU-BUILD(1)

NAME
ubuntu-build - command-line interface to Launchpad build operations SYNOPSIS
ubuntu-build <srcpackage> <release> <operation> DESCRIPTION
ubuntu-build provides a command line interface to the Launchpad build operations. OPERATIONS
Listed below are the available operations for ubuntu-build: status Outputs the build status of the package on Launchpad on all architectures. retry Requests that the package has another attempt at rebuilding from source. This will only work if the package has Failed to build on Launchpad. rescore Requests that the package's build priority be raised in the build queue. Only members of the Launchpad build administrators may issue this operation, and it may only be performed on packages which Need building. OPTIONS
Listed below are the command line options for ubuntu-build: -h or --help Display a help message and exit. Retry and rescore options: These options may only be used with the 'retry' and 'rescore' operations. -a ARCHITECTURE, --arch=ARCHITECTURE Rebuild or rescore a specific architecture. Valid architectures include: amd64, sparc, powerpc, i386, armel, armhf, ia64, lpia, hppa. Batch processing: These options and parameter ordering is only available in --batch mode. Usage: ubuntu-build --batch [options] <package>... --batch Enable batch mode --series=SERIES Selects the Ubuntu series to operate on (default: current development series) --retry Retry builds (give-back). --rescore=PRIORITY Rescore builds to <priority>. --arch2=ARCHITECTURE Affect only 'architecture' (can be used several times). Valid architectures are: amd64, sparc, powerpc, i386, armel, armhf, ia64, lpia, hppa. AUTHORS
ubuntu-build was written by Martin Pitt <martin.pitt@canonical.com>, and this manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>. Both are released under the terms of the GNU General Public License, version 3 or (at your option) any later version. ubuntu-dev-tools June 2010 UBUNTU-BUILD(1)
All times are GMT -4. The time now is 11:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy