05-27-2012
network interface -
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
linux::distribution
Linux::Distribution(3pm) User Contributed Perl Documentation Linux::Distribution(3pm)
NAME
Linux::Distribution - Perl extension to detect on which Linux distribution we are running.
SYNOPSIS
use Linux::Distribution qw(distribution_name distribution_version);
if(my $distro = distribution_name) {
my $version = distribution_version();
print "you are running $distro, version $version
";
} else {
print "distribution unknown
";
}
Or else do it OO:
use Linux::Distribution qw(distribution_name distribution_version);
my $linux = Linux::Distribution->new;
if(my $distro = $linux->distribution_name()) {
my $version = $linux->distribution_version();
print "you are running $distro, version $version
";
} else {
print "distribution unknown
";
}
DESCRIPTION
This is a simple module that tries to guess on what linux distribution we are running by looking for release's files in /etc. It now looks
for 'lsb-release' first as that should be the most correct and adds ubuntu support. Secondly, it will look for the distro specific files.
It currently recognizes slackware, debian, suse, fedora, redhat, turbolinux, yellowdog, knoppix, mandrake, conectiva, immunix, tinysofa,
va-linux, trustix, adamantix, yoper, arch-linux, libranet, gentoo, ubuntu, scientific, oracle enterprise linux and redflag.
It has function to get the version for debian, suse, fedora, redhat, gentoo, slackware, scientific, oracle enterprise linux, redflag and
ubuntu(lsb). People running unsupported distro's are greatly encouraged to submit patches :-)
EXPORT
None by default.
TODO
Add the capability of recognize the version of the distribution for all recognized distributions.
AUTHORS
Alexandr Ciornii <alexchorny@gmail.com>, <http://chorny.net> Alberto Re, <alberto@accidia.net> Judith Lebzelter, <judith@osdl.org>
COPYRIGHT AND LICENSE
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself, either Perl version 5.8.5 or,
at your option, any later version of Perl 5 you may have available.
perl v5.14.2 2012-03-18 Linux::Distribution(3pm)