My two cents:
You have an Integrity box, I only know PA-RISC... (worked with since 1993...), only I had to change a couple of times bad disks, reading the updated When Good Disks Go Bad: Dealing with Disk Failures Under LVM I would stick from your point 10 to what is to do on page 51 step 5 and 6 and do only that!
I will be away for 5 days but other here surely will take over (methyl?)
point4:
You must
because you have not rebooted OK?
so 5: you run ioscan -m lun
point 6:
I am not sure that after, you need to initialize (using the above options...)...
So check before with
Last edited by vbe; 05-23-2012 at 02:22 PM..
Reason: URL...
I dont even know what raid level this is, but its raid 5 mirrored from the looks of it.
I have a failed disk (t12) within this mirror. What is the best way to replace this disk? 2 things concern me, isn't there a command to prepare the disk for a hot swap? and what should i do with the... (3 Replies)
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Hi,
One of my disk is in 'disk missing state'. It is a sharedVG and cluster nodes.
The errpt keeps reporting stale partition error.
lvs are in open/stale state.
In this sceanario is replacing the disk the best practice?
When i do a lsdev the disk is labelled as below.
hdisk3 Available ... (2 Replies)
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
LEARN ABOUT DEBIAN
bootcd2disk
BOOTCD2DISK(1) bootcd utils BOOTCD2DISK(1)NAME
bootcd2disk - copy a system running from bootcd to a disk
SYNOPSIS
bootcd2disk [-i] [-s] [-c <config directory>] [-url <url>]
DESCRIPTION
With bootcd2disk a CD build with bootcdwrite can be copied to one or more Disk Partitions from the running cd-based system. Therefore
bootcd could be used to make rescue disks.
It is also possible to let bootcd2disk automatically find a disk, make partitions on it, copy the cd to the disk and make the disk
bootable. bootcd2disk will be available as soon as your system is running from cd.
OPTIONS -i With this option the complete bootcd2disk runs in interactive mode and you can run each function manually. This option is useful for
debugging.
-v The option "-v" (verbose) adds messages on running.
-s This option can be used to disable interactive questions and to try to ignore errors.
-c <config directory>
The configuration directory which normally is "/etc/bootcd" can be changed with this.
-url <url>
If bootcd2disk is slow on your system (because of a slow CD/DVD drive or the HP ILO virtual CD interface), you can use an image server
to get the image from. bootcd2disk use the SWAP partition of your upcoming system as temporary space and copy the image from the con-
figured image server to this partition and use it as image. The image server url is configured with this option.
example install from imagesserver:
bootcd2disk -url http://192.168.1.1/cdimage.iso
Another way the increase the performance is the use of the mounted CD/DVD itself for the copy. The option "-url" is the same, the url
starts with "file:///"
example install from CD/DVD drive sdc0:
bootcd2disk -url file:///dev/sdc0
The swap partition of the upcoming system must have enough space to get the whole image!
Currently no other options can be specified on command line. All other configuration has to be done in the config files.
FILES
/etc/bootcd/bootcd2disk.conf
Configuration for bootcd2disk.
SEE ALSO
Documentation in bootcd2disk.conf
bootcd2disk.conf(5), bootcd(1), bootcdflopcp(1), bootcdwrite(1)AUTHOR
This manual page was written by Bernd Schumacher <bernd.schumacher@hp.com> and Carsten Dinkelmann <Carsten.Dinkelmann@foobar-cpa.de> for
the Debian GNU/Linux system (but may be used by others).
bootcd2disk 2007-04-04 BOOTCD2DISK(1)