05-18-2012
Network interface-
Hello,
Please what's the difference between:
Quote:
eth1 Link encap:Ethernet HWaddr 08:00:27:3a:0d:6b
inet addr:192.168.56.102 Bcast:192.168.56.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe3a:d6b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:29 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1180 (1.1 KB) TX bytes:8350 (8.3 KB)
AND
Quote:
eth0 Link encap:Ethernet HWaddr 08:00:27:0b:17:dd
inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe0b:17dd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:25 errors:0 dropped:0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3330 (3.3 KB) TX bytes:10363 (10.3 KB)
Thank you so much
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
oidentd_masq.conf
oidentd_masq.conf(5) File Formats Manual oidentd_masq.conf(5)
NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file.
DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is
specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file.
oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option.
This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident
daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons
for windows do this, maybe others).
FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type>
The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The
mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is
equivalent to 255.255.0.0, etc.
The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param-
eter.
The third field specifies the operating system the machine matching the first parameter is running.
EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type>
192.168.1.1 someone UNIX
192.168.1.2 noone WINDOWS
192.168.1.1/32 user1 UNIX
192.168.1.0/24 user3 UNIX
192.168.0.0/16 user4 UNIX
somehost user5 UNIX
192.168.1.0/255.255.255.0 user6 UNIX
AUTHOR
Ryan McCabe <ryan@numb.org>
http://dev.ojnk.net
SEE ALSO
oidentd(8) oidentd.conf(5)
version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)