Sponsored Content
Operating Systems Solaris Interface card using a lot of bandwith Post 302639783 by misterx12345 on Sunday 13th of May 2012 07:21:18 AM
Old 05-13-2012
Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need to drill down more.

Thx.
 

9 More Discussions You Might Find Interesting

1. IP Networking

network bandwith for oracle

Hi, we should size our network (LAN and WAN) bandwidth regarding Oracle database and Oracle Applications that we will install. how to determine Bandwidth ? What is the relation between number of users, number of transactions and bandwidth ? Any Oracle documentation ? Please ? Many thanks. (0 Replies)
Discussion started by: big123456
0 Replies

2. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

3. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. Red Hat

Interface bandwith utilization in Mbps

Hi Experts, I want to plot graph for interface traffic of redhat machine. I am having hard time finding where to start. Any tools ? i found this php script which prints bytes send / received. but i need something which can give me value as mbps or kbps. If can can get output from some... (2 Replies)
Discussion started by: mtomar
2 Replies

6. IP Networking

OID for Bandwith and Throughput Measurement

Hey Guys, Does anybody know, which OID's of Net-SNMP is used to collect throughput and bandwith usage of machine?? I got these OID's ..iso.org.dod.internet.mgmt.mib-2.interfaces.ifTable.ifEntry.ifOutOctets ..1.3.6.1.2.1.2.2.1.16 ... (1 Reply)
Discussion started by: franzramadhan
1 Replies

7. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
DUMMY_CS(4)						     Kernel Interfaces Manual						       DUMMY_CS(4)

NAME
dummy_cs - PCMCIA dummy device driver SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...] DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set- ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers. It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions about card types, it is forced to rely on the card information, for better or worse. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. free_ports=n A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5). pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)
All times are GMT -4. The time now is 02:39 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy