Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value.
Is there a way where i can rename the existing/working hme1 to hme0...?
I want to showup the hmeo up if i say ifconfig -a..
rite now i see the hme1 up..
please advice if possible... (4 Replies)
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Ultra E150 Solaris 2.5.1 Oracle server. was working fine, then started losing network connection. I can see in messages file that it was complaining about another device using its ip address. Though not any longer, though I wonder if that was a red herring. My IT guys have now re-reserved its ip... (29 Replies)
Hello Folks, can anyone please help me with this ?! :wall:
I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0).
The eri0 is working great but when I try to plumb the ge0 interface ...
# ifconfig ge0 plumb
ifconfig: cannot open link... (18 Replies)
Discussion started by: pxb368@motorola
18 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)