Hi,
I have two files. 1st file has 1 column (huge file containing ~19200000 lines) and 2nd file has 2 columns (small file containing ~6000 lines).
#################################
huge_file.txt
a
a
ab
b
##################################
small_file.txt
a 1.5
b 2.5
ab ... (4 Replies)
I have two files... file1 and file2.
Where columns 1 and 2 of file1 match columns 1 and 2 of file2 I want to create a new file that is all file1 + columns 3 and 4 of file2
:b: Many thanks if you know how to do this.... :b:
file1
31-101 106 0 92
31-101 106 29 ... (2 Replies)
Hello,
I have two files which are of the following format
File 1 which has two columns
Protein_ID Substitution
NP_997239 T53R
NP_060668 V267M
NP_058515 P856A
NP_001206 T55M
NP_006601 D371Y ... (2 Replies)
Hi all, I know this sounds suspiciously like a homework course; but, it is not.
My goal is to take a file, and match my "ID" column to the "Date" column, if those conditions are true, add the total number of minutes worked and place it in this file, while not printing the original rows that I... (6 Replies)
Kindly help merging information from two files with the following data structure.
I want to match for the CHR-SNP in Foo and get the columns that match from CHROM-rsID
Fields 1 & 2 of foo may have duplicates, however, a joint key of Fields $1$2$3$4 is unique.
Also would be helpful to clean up... (4 Replies)
Hi,
i have 2 files , the data i need to match is in masterfile and i need to pull out column 3 from master if column 1 and 2 match and output entire row to new file
I have tried with join and awk and i keep getting blank outputs or same file
is there an easier way than what i am... (4 Replies)
Discussion started by: axis88
4 Replies
LEARN ABOUT NETBSD
cat
CAT(1) BSD General Commands Manual CAT(1)NAME
cat -- concatenate and print files
SYNOPSIS
cat [-beflnstuv] [-] [file ...]
DESCRIPTION
The cat utility reads files sequentially, writing them to the standard output. The file operands are processed in command line order. A
single dash represents the standard input, and may appear multiple times in the file list.
The word ``concatenate'' is just a verbose synonym for ``catenate''.
The options are as follows:
-b Implies the -n option but doesn't number blank lines.
-e Implies the -v option, and displays a dollar sign ('$') at the end of each line as well.
-f Only attempt to display regular files.
-l Set an exclusive advisory lock on the standard output file descriptor. This lock is set using fcntl(2) with the F_SETLKW command.
If the output file is already locked, cat will block until the lock is acquired.
-n Number the output lines, starting at 1.
-s Squeeze multiple adjacent empty lines, causing the output to be single spaced.
-t Implies the -v option, and displays tab characters as '^I' as well.
-u The -u option guarantees that the output is unbuffered.
-v Displays non-printing characters so they are visible. Control characters print as '^X' for control-X; the delete character (octal
0177) prints as '^?'. Non-ascii characters (with the high bit set) are printed as 'M-' (for meta) followed by the character for the
low 7 bits.
EXIT STATUS
The cat utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
The command:
cat file1
will print the contents of file1 to the standard output.
The command:
cat file1 file2 > file3
will sequentially print the contents of file1 and file2 to the file file3, truncating file3 if it already exists. See the manual page for
your shell (i.e., sh(1)) for more information on redirection.
The command:
cat file1 - file2 - file3
will print the contents of file1, print data it receives from the standard input until it receives an EOF ('^D') character, print the con-
tents of file2, read and output contents of the standard input again, then finally output the contents of file3. Note that if the standard
input referred to a file, the second dash on the command-line would have no effect, since the entire contents of the file would have already
been read and printed by cat when it encountered the first '-' operand.
SEE ALSO head(1), hexdump(1), lpr(1), more(1), pr(1), tail(1), view(1), vis(1), fcntl(2)
Rob Pike, "UNIX Style, or cat -v Considered Harmful", USENIX Summer Conference Proceedings, 1983.
STANDARDS
The cat utility is expected to conform to the IEEE Std 1003.2-1992 (``POSIX.2'') specification.
The flags [-belnstv] are extensions to the specification.
HISTORY
A cat utility appeared in Version 1 AT&T UNIX. Dennis Ritchie designed and wrote the first man page. It appears to have been cat(1).
BUGS
Because of the shell language mechanism used to perform output redirection, the command ``cat file1 file2 > file1'' will cause the original
data in file1 to be destroyed! This is performed by the shell before cat is run.
BSD September 23, 2006 BSD