04-10-2012
This post would be best posted on the HP ITRC, complete with the Operating System and version which you are running.
The essence is to disable /sbin/rc2.d/S337hpapa by configuring the parameter file which is read by that script.
This is not trivial. There is more to do.
Obviously do the work from the real console because you could lose LAN connection.
Last edited by methyl; 04-10-2012 at 10:58 PM..
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT DEBIAN
ppi::statement::break
PPI::Statement::Break(3pm) User Contributed Perl Documentation PPI::Statement::Break(3pm)
NAME
PPI::Statement::Break - Statements which break out of normal statement flow
SYNOPSIS
last;
goto FOO;
next if condition();
return $foo;
redo;
INHERITANCE
PPI::Statement::Break
isa PPI::Statement
isa PPI::Node
isa PPI::Element
DESCRIPTION
"PPI::Statement::Break" is intended to represent statements that break out of the normal statement flow control. This covers the basic
types 'redo', 'goto', 'next', 'last' and 'return'.
METHODS
"PPI::Statement::Break" has no additional methods beyond the default ones provided by PPI::Statement, PPI::Node and PPI::Element.
However, it is expected to gain methods for identifying the line to break to, or the structure to break out of.
TO DO
- Add the methods to identify the break target
- Add some proper unit testing
SUPPORT
See the support section in the main module.
AUTHOR
Adam Kennedy <adamk@cpan.org>
COPYRIGHT
Copyright 2001 - 2011 Adam Kennedy.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
The full text of the license can be found in the LICENSE file included with this module.
perl v5.10.1 2011-02-26 PPI::Statement::Break(3pm)