04-10-2012
This post would be best posted on the HP ITRC, complete with the Operating System and version which you are running.
The essence is to disable /sbin/rc2.d/S337hpapa by configuring the parameter file which is read by that script.
This is not trivial. There is more to do.
Obviously do the work from the real console because you could lose LAN connection.
Last edited by methyl; 04-10-2012 at 10:58 PM..
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
rc2(8) System Manager's Manual rc2(8)
NAME
rc2 - Run command script executed when entering a multiuser run level
SYNOPSIS
rc2
DESCRIPTION
The rc2 script contains run commands that enable initialization of the system to a multiuser state; run level 2. In addition to commands
listed within the script itself, rc2 contains instructions to run certain commands found in the /sbin/rc2.d directory. The script defines
the conditions under which the commands execute; some commands run if the system is booting, other commands execute if the system is chang-
ing run levels.
By convention, files in the /sbin/rc2.d directory begin with either the letter "K" or the letter "S" and are followed by a two-digit number
and a filename; for example: K00lpd S00savecore S25uucp
In general, the system starts commands that begin with the letter "S" and stops commands that begin with the letter "K." Commands that
begin with the letter "K" run only when the system is changing run levels from a higher to a lower level. Commands that begin with the
letter "S" run in all cases. The numbering of commands in the /sbin/rc2.d directory is important since the numbers are sorted and the com-
mands are run in ascending order. Files in the /sbin/rc2.d directory are normally links to files in the /etc/init.d directory.
An entry in the inittab file causes the system to execute the rc2 run commands, for example: s2:23:wait:/sbin/rc2 < /dev/console >
/dev/console 2>&1
The following operations are typical of those that result from executing the rc2 script and the commands located in the /sbin/rc2.d direc-
tory. The operation depends on which state the system is entering or exiting. Setting the time zone Checking the current run level Stop-
ping network services and daemons Starting (or stopping) system services and daemons Starting the cron daemon Setting up paging and dump
facilities Setting up uucp files
Setting the TIMEZONE variable is one of the first operations completed by the rc2 script. This action provides the default time zone for
subsequent commands.
FILES
Specifies the command path Specifies the directory of commands that correspond to the run level
RELATED INFORMATION
Commands: init(8), rc0(8), rc3(8) delim off
rc2(8)