04-09-2012
Break Link Aggregation in HP UX.
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please help me.
kiron
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT SUSE
ipcluster
IPCLUSTER(1) IPCLUSTER(1)
NAME
ipcluster - IPython parallel computing cluster control tool
SYNOPSIS
ipcluster {piexec,local,mpirun,pbs,ssh} [options]
DESCRIPTION
ipcluster is a control tool for IPython's parallel computing functions.
IPython cluster startup. This starts a controller and engines using various approaches. Use the IPYTHONDIR environment variable to change
your IPython directory from the default of .ipython or _ipython. The log and security subdirectories of your IPython directory will be used
by this script for log files and security files.
POSITIONAL ARGUMENTS
The first positional argument should be one of: {mpiexec, local, mpirun, pbs, ssh}, which are the available cluster types.
For detailed help on each, type "ipcluster TYPE --help". Briefly:
local run a local cluster
mpirun run a cluster using mpirun (mpiexec also works)
mpiexec run a cluster using mpiexec (mpirun also works)
pbs run a pbs cluster
ssh run a cluster using ssh, should have ssh-keys setup
OPTIONS
-h, --help
show help message and exit
EXAMPLE
ipcluster local -n 4
This command will start 4 IPython engines on the local computer.
SEE ALSO
ipython(1),ipcontroller(1),ipengine(1)
AUTHOR
ipcluster is a tool that ships with IPython, created by the IPython Development Team.
This manual page was written by Stephan Peijnik <debian@sp.or.at>, for the Debian project (but may be used by others). Modified by Fer-
nando Perez <Fernando.Perez@berkeley.edu> for inclusion in IPython.
October 28, 2008 IPCLUSTER(1)