Since your system is running Solaris7, the 'cfgadm' command did not exist back then, and I'm not even certain (without checking) whether 'devfsadm' was even around back then. You'll probably want the do the following on replacement of scsi disks:
as far as the flags output from 'metadb -i', you're just going to have to wait for a reboot to see the p,l,o and possibly m flags on that disk.
i have unix box , which currently has 2 scsi disk , as shown by format command, one at target 1 and another at target3 (which is current boot disk).
can i use both the disk , if so will df -k show usage of both ?
can any one guide me how to span file system across multiple disk. i m using sun 5.7... (4 Replies)
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
we have a SUN M3000 server.
setup as only 1 domain.
disk c0t0d0 and c0t1d0 and setup as SVM mirrors.
a few days ago disk T1 failed.
new we have replaced the disk, but can's see the disk in format.
have done cfgadm and devfsadm.
still can't access the new disk in format.
the output... (6 Replies)
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
LEARN ABOUT OSF1
reboot
reboot(8) System Manager's Manual reboot(8)NAME
reboot - Restarts the machine
SYNOPSIS
/usr/sbin/reboot [-dlnq]
DESCRIPTION
When the system is running and multiple users are logged in, use the shutdown -r command to perform a reboot operation. If no users are
logged in, use the reboot command.
The reboot command normally stops all running processes, syncs the disks, logs the reboot, and writes a shutdown entry in the login
accounting file, /var/adm/wtmp.
The reboot command uses the sync call to synchronize the disks, and to perform other shutdown activities such as resynchronizing the hard-
ware time-of-day clock. After these activities, the system reboots. By default, the system starts and the file systems are automatically
checked. If the start-up activities are successful, the system comes up in the default run-level.
You must have root privileges to use this command. Using the -n flag can result in file system damage.
FLAGS
Generates a crash dump of the system before halting it. Can be used with any of the other flags. Does not log the reboot using syslog
Does not sync the disks or log the reboot using syslog Performs a quick reboot without first shutting down running processes; does not log
the reboot using syslog
EXAMPLES
To enable the default reboot action, enter: reboot This command causes the system to stop all running processes, sync the disks, log the
shutdown, and perform other routine shutdown and reboot activities. To shut down the system without logging the reboot, enter: reboot -l
This command shuts down the system and performs all shutdown and reboot activities, except logging the shutdown. To reboot the system
abruptly, enter: reboot -q This command reboots the system abruptly without shutting down running processes.
FILES
Specifies the command path Specifies the login accounting file Specifies the path of the syslog daemon
RELATED INFORMATION
Commands: fsck(8), halt(8), init(8), savecore(8)shutdown(8), syslogd(8)
Functions: reboot(2), sync(2), syslog(3) delim off
reboot(8)