Sponsored Content
Full Discussion: Wireless Bridge/Repeater ?
Operating Systems Linux Ubuntu Wireless Bridge/Repeater ? Post 302614383 by schwasskin on Wednesday 28th of March 2012 12:36:24 PM
Old 03-28-2012
Yeah I want to get all devices on the same network in the end here. I will have to make try this out when i get home from work today.
 

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

bridge on linux

Hello. I expirince some problems with bridging, i'm pretty new to that technology I've 2 nic's 1 - wireless rt2500 ra0 canyon cn511 card 2 - e100 intel, ifconfig ra0 up && iwconfig ra0 essid xxx channel x mode managed bring me wireless connection up then i do following: brctl addbr br0... (1 Reply)
Discussion started by: hachik
1 Replies

2. IP Networking

SNMP in a Bridge device

Hello all, recently we've created a Bridge on a machine that was being used as an snmp, and we haven't assigned an IP for the bridge interface, instead we've used one extra NIC to make all the administrations, but SNMP is simply not working, any one have a clue on how to do this? Thanks. (0 Replies)
Discussion started by: Zarnick
0 Replies

3. UNIX for Dummies Questions & Answers

smc2582w-b bridge and solaris 10 wireless network

Hellow, I have a smc2582w-b brigde/acces point whom i configured on my windows vista pc and it works i have wireless acces to my network. Then i plugged it in to my 420r enterprise and it doesn't give any link activity on the lan piece of my server and my bridge/AP when i plug the cable... (3 Replies)
Discussion started by: chelle007
3 Replies

4. IP Networking

Connecting two machines with an ethernet bridge

Hello, I want to connect 2 machines with a bridge between them to control the traffic i.e. delay, loss rate, etc. I am using the following solution: 2 end machines with ip-adresses 192.168.0.8 and 192.168.0.16. 1 machine with 2 NIC interface cards: 192.168.0.40 and 192.168.0.41 I have... (9 Replies)
Discussion started by: abhishek2301
9 Replies

5. Solaris

[beginner] dladm create-bridge

hello everyone, I'm a new user and unix-beginner. I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Discussion started by: kimj
12 Replies

6. IP Networking

Create a Bridge for Qemu using only loopback

hello networking folks, i have 3 virtual machines that need to talk to each other How can i create a bridge to loopback ? -net tap,vlan=0,ifname=tap1 where tap1 is connected to lo:1 , tap2 is connected to lo:2 etc thx (0 Replies)
Discussion started by: TwiceDone
0 Replies

7. OS X (Apple)

Hostroute => Bridge and IP-Forwardings

Hello unix community, Could anyone tell me what is the macosx command for: 1) ip hostroute to bridge: ip route add 188.40.1.40/32 dev br0 (linux command) /32 ist for netmask? Because I use /29. 2) and IP-Forwarding: net.ipv4.ip_forward = 1 (linux command) I hope anyone could... (1 Reply)
Discussion started by: girlusingunyx
1 Replies
veth(4) 						     Linux Programmer's Manual							   veth(4)

NAME
veth - Virtual Ethernet Device DESCRIPTION
The veth devices are virtual Ethernet devices. They can act as tunnels between network namespaces to create a bridge to a physical network device in another namespace, but can also be used as standalone network devices. veth devices are always created in interconnected pairs. A pair can be created using the command: # ip link add <p1-name> type veth peer name <p2-name> In the above, p1-name and p2-name are the names assigned to the two connected end points. Packets transmitted on one device in the pair are immediately received on the other device. When either devices is down the link state of the pair is down. veth device pairs are useful for combining the network facilities of the kernel together in interesting ways. A particularly interesting use case is to place one end of a veth pair in one network namespace and the other end in another network namespace, thus allowing communi- cation between network namespaces. To do this, one first creates the veth device as above and then moves one side of the pair to the other namespace: # ip link set <p2-name> netns <p2-namespace> ethtool(8) can be used to find the peer of a veth network interface, using commands something like: # ip link add ve_A type veth peer name ve_B # Create veth pair # ethtool -S ve_A # Discover interface index of peer NIC statistics: peer_ifindex: 16 # ip link | grep '^16:' # Look up interface 16: ve_B@ve_A: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc ... SEE ALSO
clone(2), network_namespaces(7), ip(8), ip-link(8), ip-netns(8) COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/. Linux 2018-02-02 veth(4)
All times are GMT -4. The time now is 03:56 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy