I have one file:
123*100*abcd*10
123*101*abcd*-29*def
123*100*abcd*-10
123*102*abcd*-105*asd
I would like to parameterize the search patterns in the following way so that the user could dynamically change the search pattern.
*100* and *- (ie *minus)
*102* and *-
The output that is... (6 Replies)
hey gents,
I'm working on something that will use snmpwalk to query the devices on my network and retreive the device name, device IP, device model and device serial. I'm using Nmap for the enumeration and sed to clean up the results for use by snmpwalk. Once i get all the data organized I'm... (8 Replies)
Hi Scripting Gurus,
I am trying to parse a csv file and generate a new output file.
The input file will be a variable length in turns of rows and columns.
output file will have 8 columns. we have three columns from the header for each set.
just to give little bit more clarification each row... (15 Replies)
Hello,
I want to create a file whose content is multiple lines of strings.
The string has the following pattern:
aaaa/bbbb/A-B.txt
A is a variable ranges from A1 to A2
B is a variable ranges from B1 to B2
Any ideas?
Thanks. (17 Replies)
Hi,
i have file which contains data as below(Only sample shown, it may contain more data similar to the one shown here)
i need to read this file line by line and generate an output file like the one below
i.e based on N value the number of MSISDNs will vary, if N=1 then the following... (14 Replies)
Friends,
This is what I need:
I will pass a CSV file as an input, and I want my shell to be reading that CSV file, and based on the parameters it should generate SQLs and write those SQL in a different file in the same location.
I'm new to Shell scripting. I'm currently working on a... (1 Reply)
Friends,
This is what I need:
I will pass a CSV file as an input, and I want my shell to be reading that CSV file, and based on the parameters it should generate SQLs and write those SQL in a different file in the same location.
I'm new to Shell scripting. I'm currently working on a... (25 Replies)
Hi All,
I have a requirement where I need to go to a directory, list all the files that start with person* (for eg) & read the most recent file from the list of files.
While browsing through the forum, i found that the command ls -t will list the files. I am trying to generate the output... (1 Reply)
Hi all,
I have a single line output like below
echo $ips
10.26.208.28 10.26.208.26 10.26.208.27
want to convert above single line output as below format. Pls advice how to do ?
10.26.208.28
10.26.208.26
10.26.208.27
Regards
Kannan (6 Replies)
I would like to generate below one line report to output.txt file using csh.
01/01/09 10:15:47|APPL|MD5|ASCII-LF|6480|bal246b61fedf7e07220cedd1a100578
how to make the code to be worked ? Please advise.thanks in advance.
#!/bin/csh
a = date
set s = '|'
... (3 Replies)
Discussion started by: balajikalai
3 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)