03-09-2012
typo, sorry mksysb to /dev/rmt1 too slow
my correction, the tape device is /dev/rmt1..
it is still slow, takes 1 hr to do 1%...using mksysb -e -i /dev/rmt1
---------- Post updated at 06:12 PM ---------- Previous update was at 10:14 AM ----------
I gave up hopes but manage to find a LVD 320 drive , to be my /dev/rmt0
mksysb -e -i /dev/rmt0 took about 40 minutes or less ...completed
where before using /dev/rmt1 took about 1 hr to finish 1%...
/dev/rmt1 is my DDS-3 HP 4mm tape
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
anybody knows how to recover from a tape in AIX 4.3 from a IBM rs6000 170 system backup done only 97% ? (0 Replies)
Discussion started by: jupiter8
0 Replies
2. AIX
Hi,
Can anyone tell how to list files in a AIX 3.2 mksysb backup tape.
Thanks!
Victor Cheung (4 Replies)
Discussion started by: victorcheung
4 Replies
3. AIX
Every 3 months we have to do backups (smitth mksysb/lsmksysb + tar) on at least 30 workstations. We have to carry around 2 external tape drives to connect to them. It is a pain to do because it takes at least 3 days to do (evening/night shift) and users sometimes complain that there desk is not put... (1 Reply)
Discussion started by: Browser_ice
1 Replies
4. AIX
Hi, how can I find out though kron shell (aix 4.2) what the label of a tape is ?
Also, how can I find out if that tape has been used for an mksysb and when ? (1 Reply)
Discussion started by: Browser_ice
1 Replies
5. AIX
Hello.
I am running AIX 5.2 on a 9131-52A
I am trying to run a mksysb. I ran one on a similar 9131 and it did not take long at all. But this one is taking forever. My output is as follows:
*********************************************************
AIX:/ # mksysb -i /dev/rmt0
Creating... (2 Replies)
Discussion started by: mhenryj
2 Replies
6. AIX
I have 2 LPARs running AIX 5.3. Both are on the same VLAN. One LPAR, which I'll call LPAR2, has a 4mm SCSI tape drive connected to it, while LPAR1 does not have a tape drive connected. I am able to take mksysb backups of LPAR2 to the tape drive since it's directly connected. However, I need to... (2 Replies)
Discussion started by: need2bageek
2 Replies
7. AIX
Hello,
I am trying to install a server from a mksysb made on an other server but whit his proper image.data and bosinst.data, but after selecting boot from DLT tape and starting installation in normal mode with default setting, I get this error message :
error / warning
there is no disk... (2 Replies)
Discussion started by: astjen
2 Replies
8. AIX
Hi all,
Is it possible to boot from SMS menu boot devices into TS3200 FC tape library in case of an mksysb recovery on system p550 - 520 power6.
please note the library is fibre channel (1 Reply)
Discussion started by: h@foorsa.biz
1 Replies
9. UNIX for Beginners Questions & Answers
Hi,
I have an mksysb backup which consists of 2 Volume, how do I combine it into a single Volume or tape ?
Appreciate it (1 Reply)
Discussion started by: AIXBlueCat
1 Replies
10. AIX
Hi,
Is it possible to use mkdvd to create a bootable DVD using a mksysb on tape as the source image?
On the system concerned, we don't have enough free space to create the mksysb to file first, so would like to use the existing tape mksysb backup.
The DVD disk/s will then be used to boot a... (4 Replies)
Discussion started by: alanp36
4 Replies
RESTOR(8) System Manager's Manual RESTOR(8)
NAME
restor - incremental file system restore
SYNOPSIS
restor key [ argument ... ]
DESCRIPTION
Restor is used to read magtapes dumped with the dump command. The key specifies what is to be done. Key is one of the characters rRxt
optionally combined with f.
f Use the first argument as the name of the tape instead of the default.
r or R The tape is read and loaded into the file system specified in argument. This should not be done lightly (see below). If the key is
R restor asks which tape of a multi volume set to start on. This allows restor to be interrupted and then restarted (an icheck -s
must be done before restarting ).
x Each file on the tape named by an argument is extracted. The file name has all `mount' prefixes removed; for example, /usr/bin/lpr
is named /bin/lpr on the tape. The file extracted is placed in a file with a numeric name supplied by restor (actually the inode
number). In order to keep the amount of tape read to a minimum, the following procedure is recommended:
Mount volume 1 of the set of dump tapes.
Type the restor command.
Restor will announce whether or not it found the files, give the number it will name the file, and rewind the tape.
It then asks you to `mount the desired tape volume'. Type the number of the volume you choose. On a multivolume dump the recom-
mended procedure is to mount the last through the first volume in that order. Restor checks to see if any of the files requested
are on the mounted tape (or a later tape, thus the reverse order) and doesn't read through the tape if no files are. If you are
working with a single volume dump or the number of files being restored is large, respond to the query with `1' and restor will read
the tapes in sequential order.
If you have a hierarchy to restore you can use dumpdir(8) to produce the list of names and a shell script to move the resulting
files to their homes.
t Print the date the tape was written and the date the file system was dumped from.
The r option should only be used to restore a complete dump tape onto a clear file system or to restore an incremental dump tape onto this.
Thus
mkfs /dev/hp0a 4807
restor r /dev/hp0a
is a typical sequence to restore a complete dump. Another restor can be done to get an incremental dump in on top of this.
A dump followed by a mkfs and a restor is used to change the size of a file system.
FILES
/dev/rmt1 default file name
rst* temporary files
SEE ALSO
dump(8), dumpdir(8), mkfs(8)
DIAGNOSTICS
There are various diagnostics involved with reading the tape and writing the disk. There are also diagnostics if the i-list or the free
list of the file system is not large enough to hold the dump.
If the dump extends over more than one tape, it may ask you to change tapes. Reply with a newline when the next tape has been mounted.
Dump tapes made before the new ondisc directory structure will be converted automatically by restor .
BUGS
There is redundant information on the tape that could be used in case of tape reading problems. Unfortunately, restor does't use it.
3rd Berkeley Distribution RESTOR(8)