02-28-2012
p520 Service Processor's IP
picked up this old p520 , try many ways to connect to the SP..
a) null modem using a PC connecting to the lower S1 ...but see a bunch of
garbages across the screen once the main machine is off
b) try guessing the default IPs 192.168.3.147 and 192.168.2.147, for ports HMC1 and HMC2
no luck ..
However, I could hook up a graphical monitor where it comes up with a menu something like:
1. SMS Menu
8. Open Firmware Prompt
...etc and others..
Wonder if I could reset the IPs for the SP.
Thanks
10 More Discussions You Might Find Interesting
1. HP-UX
I am receiving messages from HP-UX Server
"The operating system is unable to communicate with the service processor.
The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ".
I need help in the following:... (1 Reply)
Discussion started by: cgege
1 Replies
2. AIX
I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this? (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
3. AIX
hello everybody.
Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please? (5 Replies)
Discussion started by: soahel
5 Replies
4. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
5. AIX
Hi Folks,
I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two... (6 Replies)
Discussion started by: shaell
6 Replies
6. AIX
I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line
The settings are correct in both sides, But I can't establish a connection.
I suspect that there's something that I should do regarding the... (3 Replies)
Discussion started by: ayman metwally
3 Replies
7. AIX
it shows up after the upgrade to SF240_415, after 2 hrs.
amber light shows up on the led of 9111-520, but alog shows:
everything seems to work, not sure what's going on.. (6 Replies)
Discussion started by: ppchu99
6 Replies
8. AIX
trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think
a few questions, on this practice AIX machine on AIX 7.1
VIO can only be installed if ASMI or HMC is running ???
if so, perhaps ASMI is much simpler, since I will need to... (2 Replies)
Discussion started by: ppchu99
2 Replies
9. AIX
picked up an old p520..and also spend sometimes to manage software:
a) AIX 7.1
b) VIOS Server 2.2
attempting to run a few LPARs without much more $$$$, as this is a home-made projects..
machine hdisk0, pre-installed with AIX 7.1
a few questions:
a) In order to run LPARs, I will... (7 Replies)
Discussion started by: ppchu99
7 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT DEBIAN
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <stgt@vger.kernel.org>
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)