dependency require_all/none svc:/network/physical (maintenance) Post: 302602030

9 More Discussions You Might Find Interesting

1. Cybersecurity

network card physical reset error

Hi all I am facing some problem with network card i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency. In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are...

2. UNIX for Dummies Questions & Answers

physical volume and physical disk.

Hello, I need explanations about physical disks and physical volumes. What is the difference between these 2 things? In fact, i am trying to understand what the AIX lspv2command does. Thank you in advance.

3. Solaris

Testing physical network connection

How do you test the physical network connection of an interface in solaris. I know that if you have an active connection and the cable gets yanked, you can look in the messages file to check for link failure messages. But is there any better way to see if you have good layer 2 connectivity?

4. UNIX for Dummies Questions & Answers

Physical volume- no free physical partitions

I was in smit, checking on disc space, etc. and it appears that one of our physical volumes that is part of a large volume group, has no free physical partitions. The server is running AIX 5.1. What would be the advisable step to take in this instance?

5. AIX

Maximum Limit of HMC to handle Physical Power Virtualization Physical Machine

Hello All, Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time? Thanks, Jenish

6. Solaris

svc:/system/filesystem/local is always in maintenance status

Hello Friends, I need to change network filesystem status as online but it always seems in maintenance mode, I appreciate your any suggestion to change its state as online. shell>svcadm enable svc:/system/filesystem/local shell>svcs -l svc:/system/filesystem/local fmri ...

7. Solaris

svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96. [ n

After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks. ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface # ifconfig eg1000g0:2 plumb ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface # ifconfig...

8. Solaris

Svc:/network/http:apache2 error

Dear All, http:apache2 service on my node is continuously in maintenance mode. I have tried to enable and disable the service but nothing works. root@ops # svcs -a | grep apache2 maintenance 15:46:37 svc:/network/http:apache2 When I reboot the system, I get the following error: ...

9. Solaris

/network/smb/server goes into maintenance mode.

All I'm running an OpenSolaris system (Nexenta). When doing a svcs I see that/network/smb/server is in maintenance mode. I have run a clear on the service and restarted. I see the same service show online* for a bit but then, enters maintenance every time. In the service log I...

LEARN ABOUT DEBIAN

irsend

IRSEND(1)							   User Commands							 IRSEND(1)

NAME

       irsend - basic LIRC program to send infra-red commands

SYNOPSIS

       irsend [options] DIRECTIVE REMOTE CODE [CODE...]

DESCRIPTION

       Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
       as TV boxes, HiFi sets, etc.

       DIRECTIVE can be:
	  SEND_ONCE	    - send CODE [CODE ...] once
	  SEND_START	    - start repeating CODE
	  SEND_STOP	    - stop repeating CODE
	  LIST		    - list configured remote items
	  SET_TRANSMITTERS  - set transmitters NUM [NUM ...]
	  SIMULATE	    - simulate IR event

       REMOTE is the name of a remote, as described in the lircd configuration file.

       CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.

       NUM is the transmitter number of the hardware device.

       For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:

	  LIST	 ""    ""   - list all configured remote names
	  LIST REMOTE  ""   - list all codes of REMOTE
	  LIST REMOTE CODE  - list only CODE of REMOTE

       The SIMULATE command only works if it has been explicitly enabled in lircd.

       -h --help
	      display usage summary

       -v --version
	      display version

       -d --device
	      use given lircd socket [/var/run/lirc/lircd]

       -a --address=host[:port]
	      connect to lircd at this address

       -# --count=n
	      send command n times

EXAMPLES

	  irsend LIST DenonTuner ""
	  irsend SEND_ONCE  DenonTuner PROG-SCAN
	  irsend SEND_ONCE  OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
	  irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
	  irsend SEND_STOP  OnkyoAmpli VOL-DOWN
	  irsend SET_TRANSMITTERS 1
	  irsend SET_TRANSMITTERS 1 3 4
	  irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"

FILES

       /etc/lirc/lircd.conf
	      Default lircd configuration file.  It should contain all the remotes, their infra-red codes and the corresponding timing	and  wave-
	      form details.

DIAGNOSTICS

       If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
       "irsend: could not connect to socket"
       "irsend: Connection refused" (or "Permission denied").

SEE ALSO

       The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.

       lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.

irsend 0.9.0-pre1						   October 2010 							 IRSEND(1)