I am very new to Unix and don't know much about it. I've been trying to create a menu and what I don't understand is how to execute a command once a user makes a selection. I have the menu set up. In fact, the following is the code that I have thus far:
#! /bin/csh
# This is the UNIX menu... (0 Replies)
Hi there. I'm trying to teach myself UNIX but the book I bought is a bit confusing. I'm trying out this exercise and I think I'm on the right track, but I'd appreciate any suggestions on how to improve what I have so far. Also, I'm not clear on how to use the read command to utilize the user's... (3 Replies)
the idea is to create script with menu and when option 1 or2 is pressed program should clear screan display info and get back to menu....
I managed some code but getting errors...
#!/bin/bash
choice1=ls -l|awk'{print $9 $1}'
choice2= ls | wc -c
choice3=exit
while
do
clear
echo "... (8 Replies)
Hopefully I'm in the right place. Im new to the forums and linux!
I'm looking to add a menu to my perl hangman game i have created. The menu will use user input for the desired option and then perform the operation indicated. I would like something along the lines of:
Welcome to Hangman... (1 Reply)
hi all i am a newbie to this
is there any examples on creating a main menu with 3 sub menu
main menu -> option a , b and c
a menu -> option 1 ,2 and 3
b menu -> option 1 ,2
c menu -> option 1 ,2
i am getting headache as my code kept getting unexpected EOF
---------- Post... (0 Replies)
Dear Sir,
May I know how do I go about adding the following feature into the script below:
When user enter values other than 1,2,3,4,
a) Message “Wrong entry !!! Pls select 1,2,3 or 4” is displayed
b) The screen is cleared again and the menu is displayed.
#!/bin/bash
clear
var=1... (2 Replies)
I am trying to make a calculator. The user Enters number 1, chooses and operation, enters number 2, then chooses another operation or for the answer to be displayed.
eg. 1 + 1 = or 1 + 1 + 2 + 1 =
Both of these should be possible.
#!/bin/bash
read -p "what's the first number? " n1... (3 Replies)
I ran the following command.
cat abc.c > abc.c
I got message the following message from command cat:
cat: abc.c : input file is same as the output file
How the command came to know of the destination file name as the command is sending output to standard file. (3 Replies)
hi all
i am trying to get help with writing a script using case statement to display menu as
1) Authentication log
2) System log
3) Messages
4) Dmesg
5) Boot log
Q) Exit
When selecting the menu by 1 or 2 or 3 o 4 or 5, it should display the last 10 lines of the log files,
if... (3 Replies)
In the bash menu below if the variant that is inputted is in the format NM_004004.3:c.274G>T the below works perfectly. My question is if the variant inputted isNM_004004.3:-c.274G>T or NM_004004.3:+c.274G>T then the code as is will throw an error due to a biological issue. Is it possible to to... (1 Reply)
Discussion started by: cmccabe
1 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)