02-23-2012
thats the configuration if you use two domains... no need to prove this. there is no command to do this from XSCF level. you can check from OBP after bringing up the domain.
10 More Discussions You Might Find Interesting
1. Solaris
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
Discussion started by: sbk1972
9 Replies
2. Solaris
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies
3. Solaris
Hi, I am now trying to setup XSCF mail reporting for a Sun M5K. There is no mail server here. Each Sun box is both its mail receiver and sender by using mailx. Mailx is working fine on this M5K.
XSCF> setsmtp
Mail Server :
Port :
Authentication Mechanism :
Reply Address:
What should I... (4 Replies)
Discussion started by: aixlover
4 Replies
4. UNIX for Advanced & Expert Users
Hi, We have two Sun M5000 systems. A is Oracle server and B is testing server. There are nine Solaris 10 zones set on A. SAN is connecting to A with ZFS configuration.
Now we want to set B to be a backup server of A and make the two as identical as possible. No VERITAS cluster, no Solaris... (3 Replies)
Discussion started by: aixlover
3 Replies
5. Solaris
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
Thank... (5 Replies)
Discussion started by: aixlover
5 Replies
6. Hardware
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Discussion started by: desertdenizen
2 Replies
7. Solaris
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Discussion started by: giles.cardew
6 Replies
8. Solaris
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Discussion started by: soupbone38
2 Replies
9. Solaris
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
Discussion started by: badoshi
3 Replies
10. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT X11R4
asadmin-list-domains
asadmin-list-domains(1AS) User Commands asadmin-list-domains(1AS)
NAME
asadmin-list-domains, list-domains - lists the domains in the given domains directory
SYNOPSIS
list-domains [--domaindir install_dir/domains] [--terse=false] [--echo=false]
list-domains lists the domains in the given domains directory. This command is supported in local mode only.
OPTIONS
--domaindir directory where the domains are located. If specified, path must be accessible in the filesystem. If not specified,
the domains in the default install_dir/domains directory are listed.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script.
--echo setting to true will echo the command line statement on the standard output.
Example 1: Using list-domains
asadmin> list-domains
List of domains:
domain1 running
samples not running
Where: the domain1 and samples are listed and their status printed.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-delete-domain(1AS), asadmin-start-domain(1AS), asadmin-stop-domain(1AS)
J2EE 1.4 SDK March 2004 asadmin-list-domains(1AS)