02-20-2012
in this configuration, half of the cpu and memory boards are in domain 1 (if 4 cpu and 8 memory modules are inside the server).
domain 0 will have the other half...
2 hdds and the dvd- and tape-drive will also belong to domain 0.
the other 2 hdds will belong to domain 1.
also every domain has one IOU board.
This User Gave Thanks to DukeNuke2 For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
Discussion started by: sbk1972
9 Replies
2. Solaris
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies
3. Solaris
Hi, I am now trying to setup XSCF mail reporting for a Sun M5K. There is no mail server here. Each Sun box is both its mail receiver and sender by using mailx. Mailx is working fine on this M5K.
XSCF> setsmtp
Mail Server :
Port :
Authentication Mechanism :
Reply Address:
What should I... (4 Replies)
Discussion started by: aixlover
4 Replies
4. UNIX for Advanced & Expert Users
Hi, We have two Sun M5000 systems. A is Oracle server and B is testing server. There are nine Solaris 10 zones set on A. SAN is connecting to A with ZFS configuration.
Now we want to set B to be a backup server of A and make the two as identical as possible. No VERITAS cluster, no Solaris... (3 Replies)
Discussion started by: aixlover
3 Replies
5. Solaris
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
Thank... (5 Replies)
Discussion started by: aixlover
5 Replies
6. Hardware
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Discussion started by: desertdenizen
2 Replies
7. Solaris
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Discussion started by: giles.cardew
6 Replies
8. Solaris
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Discussion started by: soupbone38
2 Replies
9. Solaris
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
Discussion started by: badoshi
3 Replies
10. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT XFREE86
asadmin-stop-domain
asadmin-stop-domain(1AS) User Commands asadmin-stop-domain(1AS)
NAME
asadmin-stop-domain, stop-domain - stops the given domain
SYNOPSIS
stop-domain [--domaindir install_dir/domains][--terse=false] [--echo=false] [domain_name]
stop-domain stops the specified domain. If there is only one domain in the default domain directory (install_dir/domains), then no operand
is required to stop the domain. However, if there is more than one domain, the domain operand must be specified. This command is supported
in local mode only.
OPTIONS
--domaindir directory where the domain is to be stopped. If specified, path must be accessible in the filesystem. If not speci-
fied, the domainis stopped in the default install_dir/domains directory.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
OPERANDS
domain_name name of the domain. Must be a unique name.
Example 1: Using stop-domain
asadmin> stop-domain sampleDomain
Stoping Domain sampleDomain, please wait
Domain sampleDomain stopped
Command stop-domain executed successfully
Where: the sampleDomain domain in the default domains directory is stopped.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-delete-domain(1AS), asadmin-start-domain(1AS), asadmin-list-domains(1AS)
J2EE 1.4 SDK March 2004 asadmin-stop-domain(1AS)