02-19-2012
Alternativelly you can overwrite via "dd" command VTOC table (is located on first 64K tracks of volume) and then use format.
10 More Discussions You Might Find Interesting
1. Solaris
Is there a limit to the number of LUNS that can be concatenated using Solaris Volume manager with Soft partitions?
I have worked with some AIX admins in the past and there was such a limitation therefore limiting the size the filesystem could grow to.
Is there such a limitation in Solaris 9... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
2. Solaris
Hi
I have a solaris 8 server that have LUN being removed from the server but it is still show up as error device in format command and in vxvm, i have already run devfsadm -C but it does not clear up the disk, is there other command to do this without reconfiguration boot?
34. c9t2d0... (9 Replies)
Discussion started by: robertngo
9 Replies
3. Solaris
hi all
can anyone tell me how to track a new attached LUN in a solaris server?? (3 Replies)
Discussion started by: raynu.sharma
3 Replies
4. Solaris
What is the largest possible LUN size that can be presented to Solaris 10. I've been googling a lot about this. The new EFI lablels (an alternative to VTOC) supports LUNs greater than 2TB. I need to know the upper limit. please help me find it. (4 Replies)
Discussion started by: pingmeback
4 Replies
5. Solaris
Hi,
I need to set up iscsi LUN on Solaris 9. I've done it on Solaris 10 with iscsiadm. How do you do it on Solaris 9 though? Currently using Solaris 9 update 2. Your help is appreciated.
Thanks,
Sparcman (6 Replies)
Discussion started by: sparcman
6 Replies
6. Solaris
hi,
what are the steps to detect and configure a new attached lun in Solaris 10.
Is there any difference between cfgadm and luxadm command ?
rgds,
snjksh (5 Replies)
Discussion started by: snjksh
5 Replies
7. Solaris
Hello all,
i try to allocate the same LUN to two server (or more in the future)
i use solaris 10, vxvm (vxfs) for data and solaris zones and EMC DMX-4, i try to migrate solaris zones between servers in case of problem.
and this is what i want to do
- affect LUN to srv00124 and srv10155
-... (5 Replies)
Discussion started by: mat_solaris
5 Replies
8. Solaris
How to get LUN WWN (i.e LUN mapped from a storage box say Symmetrix or clariion) in Solaris. fcinfo command does give the Target port wwn but what i'm looking for is the LUN WWN. Any help is appreciated. (2 Replies)
Discussion started by: Manish00712
2 Replies
9. Solaris
Hello to all,
Actually, currently on my Solaris box, I've a LUN (5TB space) from a EMC storage which is working fine, and a partition with ZFS filesystem is created for that LUN. as further you'll see in the logs, the "c4t6006016053802E00E6A9196B6506E211d0s2" is the current configured LUN in the... (4 Replies)
Discussion started by: Anti_Evil
4 Replies
10. Solaris
How can i remove LUN's from solaris 10 those are unmapped from SAN?
from storage side i got confirmation that they removed lun. but in my solaris box still it's visible.
i tried below.
root@globalares2.example.com #luxadm -e offline /dev/rdsk/c2t600D02310007D16C42FF09E24B5B8255d0s2... (7 Replies)
Discussion started by: bentech4u
7 Replies
LEARN ABOUT OPENSOLARIS
oplhpd
oplhpd(1M) System Administration Commands oplhpd(1M)
NAME
oplhpd - Hot plug daemon for SPARC Enterprise Server line
SYNOPSIS
/usr/platform/SUNW,SPARC-Enterprise/lib/sparcv9/lib/oplhpd
DESCRIPTION
The hot plug daemon for SPARC Enterprise Servers is a daemon process that runs on the SUNW,SPARC-Enterprise family of servers. The daemon
is started by the service management facility (see smf(5)) and communicates with the service processor when hot plug PCI cassettes change
their dynamic reconfiguration state.
The service FMRI for oplhpd is:
svc:/platform/sun4u/oplhpd:default
A domain supports only one running oplhpd process at a time.
ERRORS
OPLHPD uses syslog(3C) to report status and error messages. All of the messages are logged with the LOG_DAEMON facility.
Error messages are logged with the LOG_ERR and LOG_NOTICE priorities, and informational messages are logged with the LOG_DEBUG priority.
The default entries in the /etc/syslog.conf file log all of the OPLHPD error messages to the /var/adm/messages log.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWdcsu, SUNWdcsr |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), inetadm(1M), svcadm(1M), syslog(3C), syslog.conf(4), attributes(5), smf(5)
SunOS 5.11 23 May 2006 oplhpd(1M)