Hi Guys,
I spend half a day getting this to work with no luck, perhaps you guys can help..
I have a string from a file looking like this:
module::name=test::type=generic_data::exec=snmpget.......::desc=A Little Test::interval=300
what I would like to split it, so I get a value for each... (3 Replies)
Sorry for the duplicate thread this one is similar to the one in
https://www.unix.com/shell-programming-scripting/88132-awk-sed-script-read-values-parameter-files.html#post302255121
Since there were no responses on the parent thread since it got resolved partially i thought to open the new... (4 Replies)
Hi,
I need an awk command that would parse the below expression
Input Format
1 'Stmt1 ............................'2 'Stmt2 ............................'3 'Stmt3 ............................'4 'Stmt4 ............................'5 'Stmt5 ............................'6 'Stmt6... (1 Reply)
hi guys,
i want to parse a file using public function, the file contain raw data in the below format i want to get the output like this to load it to Oracle DB
MARWA1,BSS:26,1,3,0,0,0,0,0.00,22,22,22.00
MARWA2,BSS:26,1,3,0,0,0,0,0.00,22,22,22.00
this the file raw format:
Number of... (6 Replies)
Hi
I have a big file with a certain pattern (shown below) from which I need to parse out some digits in tabular format.
The format of the file is: '-' indicates text which doesn't to be parsed
# Output of huzzle for sequence file 1000.Clade1.html
- - - -- -------... (2 Replies)
AWK Command parse a file based on string.
I am trying to write a shell script to parse a file based on a string and move the content of the file to another file.
Here is scenario.
File content below
Mime-Version: 1.0
Content-Type: multipart/mixed;
... (2 Replies)
Hi all, I have a file that contains a good hundred of these job definitions below:
Job Name Last Start Last End ST Run Pri/Xit
________________________________________________________________ ____________________... (7 Replies)
Hi,
i am trying to get the system model with the help of awk :
$ prtconf | awk '/^System Model/'
System Model: IBM,8408-E8D
but i want just the below outout that is command should chk for pattern <IBM,> and remove it from the final output :
System Model:8408-E8D
Can... (2 Replies)
Hi All,
Seeking for your assistance on how to ouput the file which is not match in file 1 and file 2 using awk. I tried NR=FNR but it's not working, it will only show the match record.
Ex.
File1
abc
def
ghi
File2
23a
gd
abc
Output:
abc (2 Replies)
Discussion started by: znesotomayor
2 Replies
LEARN ABOUT CENTOS
export
EXPORT(1P) POSIX Programmer's Manual EXPORT(1P)PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the correspond-
ing Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux.
NAME
export - set the export attribute for variables
SYNOPSIS
export name[=word]...
export -p
DESCRIPTION
The shell shall give the export attribute to the variables corresponding to the specified names, which shall cause them to be in the envi-
ronment of subsequently executed commands. If the name of a variable is followed by = word, then the value of that variable shall be set to
word.
The export special built-in shall support the Base Definitions volume of IEEE Std 1003.1-2001, Section 12.2, Utility Syntax Guidelines.
When -p is specified, export shall write to the standard output the names and values of all exported variables, in the following format:
"export %s=%s
", <name>, <value>
if name is set, and:
"export %s
", <name>
if name is unset.
The shell shall format the output, including the proper use of quoting, so that it is suitable for reinput to the shell as commands that
achieve the same exporting results, except:
1. Read-only variables with values cannot be reset.
2. Variables that were unset at the time they were output need not be reset to the unset state if a value is assigned to the variable
between the time the state was saved and the time at which the saved output is reinput to the shell.
When no arguments are given, the results are unspecified.
OPTIONS
See the DESCRIPTION.
OPERANDS
See the DESCRIPTION.
STDIN
Not used.
INPUT FILES
None.
ENVIRONMENT VARIABLES
None.
ASYNCHRONOUS EVENTS
Default.
STDOUT
See the DESCRIPTION.
STDERR
The standard error shall be used only for diagnostic messages.
OUTPUT FILES
None.
EXTENDED DESCRIPTION
None.
EXIT STATUS
Zero.
CONSEQUENCES OF ERRORS
Default.
The following sections are informative.
APPLICATION USAGE
None.
EXAMPLES
Export PWD and HOME variables:
export PWD HOME
Set and export the PATH variable:
export PATH=/local/bin:$PATH
Save and restore all exported variables:
export -p > temp-fileunset a lot of variables... processing. temp-file
RATIONALE
Some historical shells use the no-argument case as the functional equivalent of what is required here with -p. This feature was left
unspecified because it is not historical practice in all shells, and some scripts may rely on the now-unspecified results on their imple-
mentations. Attempts to specify the -p output as the default case were unsuccessful in achieving consensus. The -p option was added to
allow portable access to the values that can be saved and then later restored using; for example, a dot script.
FUTURE DIRECTIONS
None.
SEE ALSO
Special Built-In Utilities
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2003 Edition, Standard for Information Technol-
ogy -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of
Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE
and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained
online at http://www.opengroup.org/unix/online.html .
IEEE /The Open Group 2003 EXPORT(1P)