Hardware RAID not recognize the new disk [Sun T6320] Post: 302598365

Sponsored Content

Operating Systems Solaris Hardware RAID not recognize the new disk [Sun T6320] Post 302598365 by rock123 on Tuesday 14th of February 2012 08:12:39 AM

02-14-2012

Registered User

Hardware RAID not recognize the new disk [Sun T6320]

We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue.

We have 2 LDOM configured on this server and this server running on single disk.

Code:

# raidctl -l
Controller: 0
        Volume:c0t0d0
        Volume:c0t2d0
        Disk: 0.1.0
        Disk: 0.3.0
        Disk: 0.4.0

# raidctl -l c0t0d0
Volume                  Size    Stripe  Status   Cache  RAID
        Sub                     Size                    Level
                Disk
----------------------------------------------------------------
c0t0d0                  136.6G  N/A     DEGRADED ON     RAID1
                0.1.0   136.6G          GOOD
                N/A     136.6G          FAILED

# raidctl -l c0t2d0
Volume                  Size    Stripe  Status   Cache  RAID
        Sub                     Size                    Level
                Disk
----------------------------------------------------------------
c0t2d0                  136.6G  N/A     OPTIMAL  ON     RAID1
                0.4.0   136.6G          GOOD
                0.3.0   136.6G          GOOD

Last edited by DukeNuke2; 02-14-2012 at 10:00 AM..

rock123

View Public Profile for rock123

Find all posts by rock123

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ?

2. Solaris

Sun T5120 hardware RAID question

Hi everyone I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive. My question is, how would I know when one of the drives become faulty? Thanks

3. Solaris

Add new disk to Sun StorEdge 3310 RAID

HI guys. Bit of a noob so bear with me. I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was...

4. Hardware

Sun Blade T6320 memory configuration

Can you mix DIMMs in a T6320 (sparc) blade? I have read/heard that the DIMMs in a memory bay must be identical but can you have different size DIMMs installed in the blade? For instance, can you have 1 4GB DIMM in bay 0, 2 2GB DIMMs in bay 1, 4 1 GB DIMMs in bay 2 and 2 2GB DIMMs in bay 3 for a...

5. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help.

6. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk...

7. Solaris

Solaris recognize HW Raid ??

Hardware: HP P2000 HP DL380 G7 with Solaris Software: Solaris 10 05/08 I had made a Hardware raid on P2000 and install solaris on G7, The raid card controller is working fine. How can I make the raid works on OS?? "raidclt" is getting nothing :wall::wall: Thanks

8. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The...

9. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My...

LEARN ABOUT NETBSD

ataraid

ATARAID(4)						   BSD Kernel Interfaces Manual 						ATARAID(4)

NAME

     ataraid -- software BIOS RAID

SYNOPSIS

     pseudo-device ataraid
     ld* at ataraid? vendtype ? unit ?

DESCRIPTION

     The ataraid driver provides support for BIOS-based software RAID controllers.  These are devices which have some simple support for several
     basic RAID levels (often RAID 0 and RAID 1), but which require software support to actually perform the RAID function.  The BIOS support is
     largely just to create and recognize the array so that it may be a boot device.

     The driver currently supports RAID formats from:
	   o   Adaptec HostRAID (found in Intel 6300ESB)
	   o   Intel MatrixRAID
	   o   JMicron RAID
	   o   nVidia MediaShield
	   o   Promise FastTrak
	   o   Via V-RAID (found in many VIA-based motherboards)

     Status of the logical disk as well as the disks associated with it, can be viewed through the bioctl(8) utility.

SEE ALSO

     ld(4), bioctl(8)

HISTORY

     The ataraid driver first appeared in NetBSD 2.0.

AUTHORS

     The ataraid driver was originally adapted from FreeBSD by Jason Thorpe <thorpej@NetBSD.org>.

BUGS

     Not all features of the software RAID are currently recognized or supported.  For example, the Adaptec support doesn't recognize when a RAID
     1 should be in a ``building'' state, and it does not do the right thing.

     At least part of the reason for this is that the publically-available information on these formats is quite limited.

BSD
								September 16, 2008							       BSD