02-09-2012
Are your disks identical?
If strictly identical, there is an option you should try: vgreduce or split the mirror to have only one disk in vg00 then do a dd...
It should boot...
dont forget to turn off the VG_AUTO_ACTIVATE for vg01... for you will need to import the correct definition of the VG (dont know how you will do that though for SAN is not the same...)
My 2 cents:
I would go and boot the system, that will complain (duplicate address) so try to boot single user modify all that is need, ( /etc/lvmtab, fstab etc...) give a new IP and get your network team to create a VLAN so you can use it even if you are the only node in that sublan...
Once OK, activate you mirroring...
Now add vg01 (pvcreate etc...) and create all lvm as on the original.
Either copy or restore (if you backup utility will do such tasks...).
All this should be done at init level2 to be safe with no fancy unwanted overhead.
this sort of manipulation were my daily routine one time, but long, long ago...
An L3000 had at configuration/order time an option at order: you could choose a tape drive OR a DVD internal... If you wanted both you had to choose which device was external.. I had both and believe the internal tape was the best choice...
P.S.
I did also use the mirror, but had some much issues I gave up... the best of all is by far the Ignite tape, since you can start almost a fresh "install" and configure the new box immediately by giving his new name , IP etc...
Ever considered Ignite via LAN?
This User Gave Thanks to vbe For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Is there anyone out there who knows anything about
aix cloning?
I would be very grateful for any information at all.
Thanking you in advance
:) (4 Replies)
Discussion started by: annette
4 Replies
2. Filesystems, Disks and Memory
I'm looking for software that can clone Unix Partitions. (2 Replies)
Discussion started by: jimv2502893
2 Replies
3. SCO
Hello everybody,
:confused:
I have to change the system disk on an old PC running SCO 5.0.5.
The disk is up and running, this is a preventive action.
My experience on UNIX is very limited and I look for the easyest solution to clone this unit.
Is it possible with commands or through a clone... (2 Replies)
Discussion started by: mhachez
2 Replies
4. UNIX for Dummies Questions & Answers
Good day all.
So, here's the situation. I have (7x) B180L VISUALIZE WORKSTATION's with Transtec 5100 RAID (RAID 5, 9.1 GB HDD's) towers running of UNIX HP10.20. It's time to replace the RAID's with new ones, them being Fibrenetix FX606 5 bay SATA RAID, 5 bay SATA-SCSI desktop RAID including 80Gb... (1 Reply)
Discussion started by: Tony_dw
1 Replies
5. Red Hat
I wish to clone a RedHat EL5 server. What's the easiest way to do this?
Thanks :) (4 Replies)
Discussion started by: wazzu62
4 Replies
6. Shell Programming and Scripting
Hi,
Is there disadvantages if we do AIX Serevr cloning to the new AIX server.
Thanks in advance (0 Replies)
Discussion started by: kmsekhar
0 Replies
7. AIX
Hi,
Is there disadvantages if we do AIX Serevr cloning to the new AIX server.
Thanks in advance (2 Replies)
Discussion started by: kmsekhar
2 Replies
8. Ubuntu
I am using 'dd' to clone an entire hard drive which only has Ubuntu 11.10 and some data with no special options. The disks are both 1Tb, However, I did re-partition the target disk with gparted successfully. The new partions are not the same size as the source disk. When starting 'dd' no partitions... (24 Replies)
Discussion started by: Royalist
24 Replies
9. Linux
Dear All
I needed to clone my disk to another hard drive . I did it as the following :
#dd if=/dev/sdb of=/dev/sdc
But after a while, the procedure ended with the "writing to /dev/sdc
input/output error" message.
Can you please let me know how can I overcome this as the fdisk now returns as "... (1 Reply)
Discussion started by: hadimotamedi
1 Replies
LEARN ABOUT REDHAT
amverify
AMVERIFY(8) System Manager's Manual AMVERIFY(8)
NAME
amverify - check an Amanda tape for errors
SYNOPSIS
amverify config [ slot [ runtapes ] ]
DESCRIPTION
Amverify reads an Amanda format tape and makes sure each backup image can be processed by amrestore and, if possible, the appropriate
restore program (e.g. tar).
Amverify runs amrestore on each file of the tape and pipes the output to a restore program (if available) with an option to create a cata-
logue of the backup. The catalogue itself is discarded. Only the success or failure of the operation itself is reported.
If the backup image cannot be processed by the restore program, e.g. if it was written on a different operating system, the image is sent
through dd to /dev/null. This still determines if the tape is readable, but does not do any internal consistency check on the image.
If config is set up to use a tape changer, the slot argument may be used to choose the first tape to process. Otherwise, the current slot
is used.
The runtapes configuration parameter determines how many tapes are processed unless it is specified on the command line.
See the amanda(8) man page for more details about Amanda.
AUTHOR
Axel Zinser <fifi@icem.de>
SEE ALSO
amrestore(8), amanda(8), amverifyrun(8)
AMVERIFY(8)