Sponsored Content
Operating Systems Solaris Solaris 10 Changing of nic link_speed Post 302597122 by freshmeat on Thursday 9th of February 2012 08:57:54 AM
Old 02-09-2012
Quote:
Originally Posted by jlliagre
Is e1000g0 connected to the same switch as e1000g1 and e1000g2 ?
yesSmilie:

Last edited by fpmurphy; 02-09-2012 at 10:14 AM..
 

9 More Discussions You Might Find Interesting

1. IP Networking

not able to add nic in solaris 8

Hi Folks, I've just installed solaris 8, but i cannot add my network card. i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it. Kind Regards (3 Replies)
Discussion started by: noripsni
3 Replies

2. UNIX for Advanced & Expert Users

Changing MAC address of a NIC

All, I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up? Is it a missing (to me) part of ifconfig ? If so, what is the syntax? All replies gratefully received ! Thanks Andrew (3 Replies)
Discussion started by: wretch
3 Replies

3. Solaris

NIC drivers+solaris 10

Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Discussion started by: srinivas2828
1 Replies

4. Red Hat

changing ethernet NIC names?

I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

6. Solaris

Solaris, identifying NIC hw issues

Can someone point out which steps are to be done to get information if NIC on Solaris is malfunctioned and/or not working properly. Since my Solaris knowledge is very modest, i would apreciate any help. OS is Solaris 10 x86 Regards. Peasant. ---------- Post updated at 11:57 AM... (0 Replies)
Discussion started by: Peasant
0 Replies

7. Solaris

NIC detection problem in solaris

Hi, Hardware: Mother board: Asus P5G4IC-M LX On board NIC: PCIe Gigabite LAN Kernel Ver.: SunOS 5.10 Generic_141445-09 I've NIC detection problem in Solaris 10. When I was trying to install in x86 machine, it was not asking for any Network settings which means it couldn't find NIC. But... (7 Replies)
Discussion started by: vicky86ind
7 Replies

8. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

9. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
ppmtopgm(1)						      General Commands Manual						       ppmtopgm(1)

NAME
ppmtopgm - convert a portable pixmap into a portable graymap SYNOPSIS
ppmtopgm [ppmfile] DESCRIPTION
Reads a portable pixmap as input. Produces a portable graymap as output. The output is a "black and white" rendering of the original image, as in a black and white photograph. The quantization formula used is .299 r + .587 g + .114 b. Note that although there is a pgmtoppm program, it is not necessary for simple conversions from pgm to ppm , because any ppm program can read pgm (and pbm ) files automatically. pgmtoppm is for colorizing a pgm file. Also, see ppmtorgb3 for a different way of converting color to gray. And ppmdist generates a grayscale image from a color image, but in a way that makes it easy to differentiate the original colors, not necessarily a way that looks like a black and white photograph. QUOTE
Cold-hearted orb that rules the night Removes the colors from our sight Red is gray, and yellow white But we decide which is right And which is a quantization error. SEE ALSO
pgmtoppm(1),ppmtorgb3(1),rgb3toppm(1),ppmdist(1),ppm(5),pgm(5) AUTHOR
Copyright (C) 1989 by Jef Poskanzer. 10 April 2000 ppmtopgm(1)
All times are GMT -4. The time now is 08:13 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy